參數資料
型號： PCA9665
廠商： NXP Semiconductors N.V.
英文描述： Fm+ parallel bus to I2C-bus controller
中文描述： 調頻并行總線I2C總線控制器
文件頁數： 58/91頁
文件大小： 372K
代理商： PCA9665
PCA9665_2
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 7 December 2006
58 of 91
NXP Semiconductors
PCA9665
Fm+ parallel bus to I
2
C-bus controller
8.8.4
I2CSTA = 78h
This status code indicates that the SCL line is stuck LOW.
8.9 Some special cases
The PCA9665 has facilities to handle the following special cases that may occur during a
serial transfer.
8.9.1
Simultaneous repeated START conditions from two masters
A repeated START condition may be generated in the Master Transmitter or Master
Receiver modes. A special case occurs if another master simultaneously generates a
repeated START condition (see
Figure 15
). Until this occurs, arbitration is not lost by
either master since they were both transmitting the same data.
If the PCA9665 detects a repeated START condition on the I
2
C-bus before generating a
repeated START condition itself, it will use the repeated START as its own and continue
with the sending of the slave address.
8.9.2
Data transfer after loss of arbitration
Arbitration may be lost in the Master Transmitter and Master Receiver modes. Loss of
arbitration is indicated by the following states in I2CSTA; 38h, 68h, and B0h (see
Figure 7
,
Figure 11
,
Figure 8
, and
Figure 12
).
Remark:
In order to exit state 38h, a Time-out, Reset, or external STOP are required.
If the STA flag in I2CCON is set by the routines which service these states, then, if the bus
is free again, a START condition (state 08h) is transmitted without intervention by the
CPU, and a retry of the total serial transfer can commence.
8.9.3
Forced access to the I
2
C-bus
In some applications, it may be possible for an uncontrolled source to cause a bus
hang-up. In such situations, the problem may be caused by interference, temporary
interruption of the bus or a temporary short-circuit between SDA and SCL.
If an uncontrolled source generates a superfluous START or masks a STOP condition,
then the I
2
C-bus stays busy indefinitely. If the STA flag is set and bus access is not
obtained within a reasonable amount of time, then a forced access to the I
2
C-bus is
possible. If the I
2
C-bus stays idle for a time period equal to the time-out period, then the
PCA9665 concludes that no other master is using the bus and sends a START condition.
Fig 15. Simultaneous repeated START conditions from 2 masters
S
SLA
W
A
DATA
A
18h
28h
002aab028
other master sends
repeated START condition earlier
08h
S
both masters continue
with SLA transmission
相關PDF資料
PDF描述
PCA9665N Fm+ parallel bus to I2C-bus controller
PCA9671 Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DB Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DK Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9673 Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset
相關代理商/技術參數
參數描述
PCA9665APW,118 功能描述:I2C 接口集成電路 Fm+ parallel bus I2C bus controller RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665BS,118 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665BS-T 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665D 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665D,112 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*