參數資料
型號: MC68HC05T16B
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56
封裝: PLASTIC, SDIP-56
文件頁數: 59/128頁
文件大小: 734K
代理商: MC68HC05T16B
MOTOROLA
4-6
MC68HC05T16
RESETS AND INTERRUPTS
4
4.2.2
Software Interrupt (SWI)
The software interrupt is an executable instruction. The action of the SWI instruction is similar to
the hardware interrupts. The SWI is executed regardless of the state of the interrupt mask in the
condition code register. The service routine address is specied by the contents of memory
location $FFFC and $FFFD.
4.2.3
External Interrupt (IRQ)
The external interrupt IRQ can be software congured for “negative-edge” or “negative-edge and
level” sensitive triggering by the IRQN bit in the Multi-Function Timer register.
IRQN
1 (set)
Negative edge triggering for IRQ only.
0 (clear) –
Level and negative edge triggering for IRQ.
When the signal of the external interrupt pin, IRQ, satises the condition selected, an external
interrupt occurs. The actual processor interrupt is generated only if the interrupt mask bit of the
condition code register is also cleared. When the interrupt is recognized, the current state of the
processor is pushed onto the stack and the interrupt mask bit in the condition code register is set.
This masks further interrupts until the present one is serviced. The service routine address is
specied by the contents of $FFF8 & $FFF9.
The interrupt logic recognizes negative edge transitions and pulses (special case of negative
edges) on the external interrupt line. Figure 4-3 shows both a block diagram and timing for the
interrupt line (IRQ) to the processor. The rst method is used if pulses on the interrupt line are
spaced far enough apart to be serviced. The minimum time between pulses is equal to the number
of cycles required to execute the interrupt service routine plus 21 cycles. Once a pulse occurs, the
next pulse should not occur until the MCU software has exited the routine (an RTI occurs). The
second conguration shows several interrupt lines wired-OR to perform the interrupt at the
processor. Thus, if the interrupt lines remain low after servicing one interrupt, the next interrupt is
recognized.
Note:
The internal interrupt latch is cleared in the rst part of the service routine; therefore,
one (and only one) external interrupt pulse could be latched during tILIL and serviced
as soon as the I bit is cleared.
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
Multi-Function Timer Register
$1C
TOF
RTIF
TOFIE
RTIE
IRQN WDOG
RT1
RT0
0000 0011
TPG
34
相關PDF資料
PDF描述
MC68HC705V8CFU 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP64
MC68HC705V8B 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP56
MC68HC705V8FN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC68
MC68HC705V8CFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC68
MC68HC705X4CDW 8-BIT, OTPROM, 2.2 MHz, MICROCONTROLLER, PDSO28
相關代理商/技術參數
參數描述
MC68HC05V12 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontreller Unit
MC68HC05V12CFN 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification
MC68HC05X16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor HCMOS) microcontroller unit
MC68HC05X32 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor HCMOS) microcontroller unit
MC68HC05X4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit