- 您現在的位置：買賣IC網 > PDF目錄45220 > MC68HC05F4FB (MOTOROLA INC) 8-BIT, MROM, 1.789 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | MC68HC05F4FB |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 1.789 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | QFP-44 |
| 文件頁數： | 61/130頁 |
| 文件大?。?/td> | 2089K |
| 代理商： | MC68HC05F4FB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁
MOTOROLA
3-6
MC68HC05F4
MEMORY AND REGISTERS
3
EEPGM — EEPROM programming power enable
1 (set)
–
Programming power connected to the EEPROM array.
0 (clear) –
Programming power switched off.
EEPGM must be set to enable the EEPGM function. When set, EEPGM turns on the charge pump
and enables the programming (or erasing) power to the EEPROM array. When clear, this power is
switched off. This will enable pulsing of the programming voltage to be controlled internally. This
bit can be read at any time, but can only be written to if LATCH = 1, i.e. if LATCH is not set, then
EEPGM cannot be set. Reset clears this bit.
3.5.2
Programming and erasing procedures
To program a byte of EEPROM, set LATCH = CPEN = 1, set ER1 = ER0 = 0, write data to the
desired address and then set EEPGM for a time tEPGM.
There are three possibilities for erasing data from the EEPROM array, depending on how much
data is affected.
To erase a byte of EEPROM, set LATCH = CPEN = 1, set ER1 = 0 and ER0 = 1, write data to
the desired address and then set EEPGM for a time tEBYTE.
To erase a block of EEPROM, set LATCH = CPEN = 1, set ER1 = 1 and ER0 = 0, write data
to any address in the block and then set EEPGM for a time tEBLOCK.
To bulk erase the EEPROM, set LATCH = CPEN = 1, set ER1 = ER0 = 1, write data to any
address in the array and then set EEPGM for a time tEBULK.
To terminate the programming or erase sequence, clear EEPGM, wait for a time tFPV to allow the
programming voltage to fall, and then clear LATCH and CPEN to release the buses. Following
each erase or programming sequence, clear all programming control bits.
3.5.3
Sample EEPROM programming sequence
The following program is an example of the EEPROM programming sequence, using the timer to
implement the required delay and assuming a 1 MHz bus frequency.
TPG
32
05F4Book Page 6 Tuesday, August 5, 1997 1:10 pm
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05F5FN | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC05F5P | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC05F5CFN | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC05F8B | 8-BIT, MROM, 1.8 MHz, MICROCONTROLLER, PDIP56 |
| MC68HC05F8FU | 8-BIT, MROM, 1.8 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05F5 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit |
| MC68HC05F6 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MCU with DTMF/melody generator |
| MC68HC05F6P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| MC68HC05F8 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:High-density complementary metal oxide semiconductor(HCMOS) microcontroller unit |
| MC68HC05J1 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
發布緊急采購，3分鐘左右您將得到回復。