參數資料
型號: MC68CK338CPV14B1
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 32-BIT, 14.4 MHz, MICROCONTROLLER, PQFP144
封裝: PLASTIC, TQFP-144
文件頁數: 17/133頁
文件大?。?/td> 944K
代理商: MC68CK338CPV14B1
MC68CK338
MOTOROLA
MC68CK338TS/D
113
NOTES:
1. Tested with a 32.768 kHz reference.
2. All internal registers retain data at 0 Hz.
3. Assumes that stable VDDSYN is applied, and that the crystal oscillator is stable. Lock time is measured from
the time VDD and VDDSYN are valid until RESET is released. This specification also applies to the period re-
quired for PLL lock after changing the W and Y frequency control bits in the synthesizer control register (SYN-
CR) while the PLL is running, and to the period required for the clock to lock after LPSTOP.
4. This parameter is periodically sampled rather than 100% tested.
5. Assumes that a low-leakage external filter network is used to condition clock synthesizer input voltage. Total
external resistance from the XFC pin due to external leakage must be greater than 15 M
to guarantee this
specification. Filter network geometry can vary depending upon operating environment.
6. Proper layout procedures must be followed to achieve specifications.
7. Internal VCO frequency (fVCO) is determined by SYNCR W and Y bit values.
The SYNCR X bit controls a divide-by-two circuit that is not in the synthesizer feedback loop.
When X = 0, the divider is enabled, and fsys = fVCO ÷ 4.
When X = 1, the divider is disabled, and fsys = fVCO ÷ 2.
X must equal one when operating at maximum specified fsys.
8. Jitter is the average deviation from the programmed frequency measured over the specified interval at max-
imum fsys. Measurements are made with the device powered by filtered supplies and clocked by a stable ex-
ternal clock signal. Noise injected into the PLL circuitry via VDDSYN and VSS and variation in crystal oscillator
frequency increase the Jclk percentage for a given interval. When clock jitter is a critical constraint on control
system operation, this parameter should be measured during functional testing of the final system.
Table 69 Clock Control Timing
(V
DD
and V
DDSYN
= 2.7 to 3.6 Vdc, V
SS
= 0 Vdc, T
A
= T
L
to T
H
)
Num
Characteristic
Symbol
Min
Max
Unit
1
PLL Reference Frequency Range1
f
ref
25
50
kHz
2
System Frequency2
On-Chip PLL System Frequency Range
External Clock Operation
f
sys
dc
4(fref)
dc
14.4
MHz
3
PLL Lock Time1, 3, 4, 5, 6
t
lpll
20
ms
4
VCO Frequency7
fVCO
2 (fsys max)
MHz
5
Limp Mode Clock Frequency
SYNCR X bit = 0
SYNCR X bit = 1
f
limp
f
sys
max/2
f
sys
max
MHz
6
CLKOUT Jitter1, 4, 5, 6, 8
Short term (5
s interval)
Long term (500
s interval)
J
clk
– 0.5
– 0.05
0.5
0.05
%
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68CK338CPV14 32-BIT, 14.4 MHz, MICROCONTROLLER, PQFP144
MC68EN360CRC25 32-BIT, 25 MHz, RISC MICROCONTROLLER, CPGA241
MC68F333FE 32-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, CQFP160
MC68F333FC 32-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, PQFP160
MC68HC000L12F 16-BIT, 16.67 MHz, MICROPROCESSOR, CDIP64
相關代理商/技術參數
參數描述
MC68CM16Z1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CM16Z1CFC16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CM16Z1CPV16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68E360VR25VLR2 功能描述:微處理器 - MPU QUICC ETHRN RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC68E360ZP25VLR2 功能描述:IC MPU QUICC 32BIT 357-PBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:M683xx 標準包裝:1 系列:MPC85xx 處理器類型:32-位 MPC85xx PowerQUICC III 特點:- 速度:1.2GHz 電壓:1.1V 安裝類型:表面貼裝 封裝/外殼:783-BBGA,F(xiàn)CBGA 供應商設備封裝:783-FCPBGA(29x29) 包裝:托盤