參數資料
型號： LXT350PE
英文描述： PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC
中文描述： 的PCM收發器|單|優稅PCM-30/E-1 |的CMOS | LDCC | 28腳|塑料
文件頁數： 14/50頁
文件大?。?/td> 1197K
代理商： LXT350PE
LXT350
—
T1/E1 Short Haul Transceiver with Crystal-less Jitter Attenuation
14
Datasheet
2.0
Functional Description
The LXT350 is a fully integrated, PCM transceiver for short-haul, 1.544 Mbps (T1) or 2.048 Mbps
(E1) applications allowing full-duplex transmission of digital data over existing twisted-pair
installations. It interfaces with two twisted-pair lines (one pair each for transmit and receive)
through standard pulse transformers and appropriate resistors.
The figure on the front page of this data sheet shows a block diagram of the LXT350. The designer
can configure the device for either Host or Hardware control. In Host mode, control is via the serial
microprocessor port. In Hardware mode, individual pin settings allow stand-alone operation.
The transceiver provides a high-precision, crystal-less jitter attenuator. The user may place it in the
transmit or receive path, or bypass it completely.
The LXT350 meets or exceeds FCC, ANSI T1 and AT&T specifications for CSU and DSX-1
applications, as well as ITU and ETSI requirements for E1 ISDN PRI applications.
2.1
Initialization
During power up, the transceiver remains static until the power supply reaches approximately 3 V.
Upon crossing this threshold, the device begins a 32 ms reset cycle to calibrate the Phase Lock
Loops (PLL). The transceiver uses a reference clock to calibrate the PLLs: the transmitter reference
is TCLK, and the receiver reference clock is MCLK. MCLK is mandatory for chip operation and
must be an independent free running jitter free reference clock.
2.1.1
Reset Operation
A reset operation initializes the status and state machines for the LOS, AIS, and QRSS blocks. In
Hardware mode, holding pins RLOOP, LLOOP and TAOS High for at least one clock cycle resets
the device. In Host mode, writing a 1 to the bit CR2.RESET commands a reset which clears all
registers to 0. Allow 32 ms for the device to settle after removing all reset conditions.
2.2
Transmitter
2.2.1
Transmit Digital Data Interface
Input data for transmission onto the line is clocked serially into the device at the TCLK rate. TPOS
and TNEG are the bipolar data inputs. In Unipolar mode, the TDATA pin accepts unipolar data.
Input data may pass through either the Jitter Attenuator or B8ZS/HDB3 encoder or both. In Host
mode, setting CR1.ENCENB = 1 enables B8ZS/HDB3 encoding. In Hardware mode, connecting
the MODE pin to Midrange selects zero suppression coding. With zero suppression enabled, the
EC1 through EC3 inputs determine the coding scheme as listed in
Table 10 on page 29
.
TCLK supplies input synchronization. See the
Figure 16 on page 43
for the transmit timing
requirements for TCLK and the Master Clock (MCLK).
相關PDF資料
PDF描述
LXT361LE Telecommunication IC
LXT361PE Telecommunication IC
LXT362LE PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC
LXT362PE PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|LDCC|28PIN|PLASTIC
LXT362QE PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC
相關代理商/技術參數
參數描述
LXT350QE 制造商:LEVEL1 功能描述:
LXT351 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:T1/E1 Short Haul Transceiver with Crystal-less Jitter Attenuation
LXT351PE 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|LDCC|28PIN|PLASTIC
LXT351QE 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|QFP|44PIN|PLASTIC
LXT360 制造商:LVL1 制造商全稱:LVL1 功能描述:Integrated T1/E1 LH/SH Transceivers for DS1/DSX-1/CSU or NTU/ISDN PRI Applications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*