參數資料
型號： GT28F320D18B120
英文描述： x16 Flash EEPROM
中文描述： x16閃存EEPROM
文件頁數： 16/83頁
文件大小： 836K
代理商： GT28F320D18B120
28F320D18
12
Product Preview
3.2.3
Unlocked State
Unlocked blocks (states [000], [100], [110]) can be programmed or erased. All unlocked blocks
return to the locked state when the device is reset or powered down. The status of an unlocked
block can be changed to locked or locked-down using the appropriate command. A locked block
can be unlocked by writing the Unlock command sequence, 60H followed by D0H.
3.2.4
Lock-Down State
Blocks that are locked-down (state [011]) are protected from program and erase operations (just
like locked blocks), but their protection status cannot be changed using software commands alone.
A locked or unlocked block can be locked-down by writing the Lock-Down command sequence,
60H followed by 2FH. Locked-down blocks revert to the locked state when the device is reset or
powered down.
The Lock-Down function is dependent on the WP# input pin. When WP# = 0, blocks in lock-down
[011] are protected from program, erase, and lock status changes. When WP# = 1, the lock-down
function is disabled ([111]) and locked-down blocks can be individually unlocked by software
command to the [110] state, where they can be erased and programmed. These blocks can then be
re-locked [111] and unlocked [110] as desired while WP# remains high. When WP# goes low,
blocks that were previously locked-down return to the lock-down state [011] regardless of any
changes made while WP# was high. Device reset or power-down resets all blocks, including those
in lock-down, to locked state.
3.2.5
Reading a Block’s Lock Status
The lock status of every block can be read in the device identifier read mode of the device. To enter
this mode, write 90H to the device. Subsequent reads at Block Base Address + 00002 will output
the lock status of that block. The lock status is represented by the lowest two output pins, DQ
0
and
DQ
1
. DQ
0
indicates the block lock/unlock status and is set by the Lock command and cleared by
the Unlock command. It is also automatically set when entering lock-down. DQ
1
indicates lock-
down status and is set by the lock-down command. It cannot be cleared by software, only by device
reset or power-down.
3.2.6
Locking Operations during Erase Suspend
Changes to block lock status can be performed during an erase suspend by using the standard
locking command sequences to unlock, lock, or lock-down a block. This is useful in the case when
another block needs to be updated while an erase operation is in progress.
Table 4. Block Lock Status
Item
Address
Data
Block Lock Configuration
Block Base Address +002
LOCK
Block Is Unlocked
DQ
0
= 0
Block Is Locked
DQ
0
= 1
Block Is Locked-Down
DQ
1
= 1
相關PDF資料
PDF描述
GT3-20DP-2.5DSA Antenna, Sensor, and Communications Trunk Line Connections
GT3TK-36DP-DSA Antenna, Sensor, and Communications Trunk Line Connections
GT3TK-48TP-DS Antenna, Sensor, and Communications Trunk Line Connections
GT3-16DP-2.5DSA Antenna, Sensor, and Communications Trunk Line Connections
GT3B-16DP-2.5DSA Antenna, Sensor, and Communications Trunk Line Connections
相關代理商/技術參數
參數描述
GT28F320S3-100 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:WORD-WIDE FlashFile⑩ MEMORY FAMILY
GT28F320S3-120 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:WORD-WIDE FlashFile MEMORY FAMILY
GT28F320W18BC60 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel? Wireless Flash Memory
GT28F320W18BC80 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel? Wireless Flash Memory
GT28F320W18BD60 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel㈢ Wireless Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*