- 您現在的位置：買賣IC網 > PDF目錄17109 > EVAL-ADUC824QSZ (Analog Devices Inc)KIT DEV QUICK START ADUC824 PDF資料下載
參數資料
| 型號： | EVAL-ADUC824QSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 46/68頁 |
| 文件大小： | 0K |
| 描述： | KIT DEV QUICK START ADUC824 |
| 標準包裝： | 1 |
| 系列： | QuickStart™ 套件 |
| 類型： | MCU |
| 適用于相關產品： | ADuC824 |
| 所含物品： | 評估板，線纜，電源，軟件和文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
REV. B
ADuC824
–50–
I
2C-COMPATIBLE INTERFACE
The ADuC824 supports a 2-wire serial interface mode which is
I
2C compatible. The I2C-compatible interface shares its pins
with the on-chip SPI interface and therefore the user can only
enable one or the other interface at any given time (see SPE in
I2CADD
I
2C Address Register
Function
Holds the I
2C peripheral address for
the part. It may be overwritten by
user code. Technical Note uC001 at
describes the format of the I
2C stan-
dard 7-bit address in detail.
SFR Address
9BH
Power-On Default Value
55H
Bit Addressable
No
I2CDAT
I
2C Data Register
Function
The I2CDAT SFR is written by the
user to transmit data over the I
2C
interface or read by user code to read
data just received by the I
2C interface
Accessing I2CDAT automatically
clears any pending I
2C interrupt and
the I2CI bit in the I2CCON SFR.
User software should only access
I2CDAT once per interrupt cycle.
SFR Address
9AH
Power-On Default Value
00H
Bit Addressable
No
SPICON previously). An Application Note describing the
operation of this interface as implemented is available from
the MicroConverter Website at www.analog.com/microconverter.
This interface can be configured as a Software Master or Hard-
ware Slave, and uses two pins in the interface.
SDATA (Pin 27)
Serial Data I/O Pin
SCLOCK (Pin 26)
Serial Clock
Three SFRs are used to control the I2C-compatible interface. These are described below:
I2CCON
I
2C Control Register
SFR Address
E8H
Power-On Default Value
00H
Bit Addressable
Yes
O
D
ME
D
MO
C
MI
D
MM
C
2
IS
R
C
2
IX
T
C
2
II
C
2
I
Table XX. I2CCON SFR Bit Designations
Bit
Name
Description
7
MDO
I
2C Software Master Data Output Bit (MASTER MODE ONLY)
This data bit is used to implement a master I2C transmitter interface in software. Data written to this
bit will be outputted on the SDATA pin if the data output enable (MDE) bit is set.
6
MDE
I
2C Software Master Data Output Enable Bit (MASTER MODE ONLY)
Set by user to enable the SDATA pin as an output (Tx).
Cleared by the user to enable SDATA pin as an input (Rx).
5
MCO
I
2C Software Master Clock Output Bit (MASTER MODE ONLY)
This data bit is used to implement a master I2C transmitter interface in software. Data written to
this bit will be outputted on the SCLOCK pin.
4
MDI
I
2C Software Master Data Input Bit (MASTER MODE ONLY)
This data bit is used to implement a master I2C receiver interface in software. Data on the SDATA
pin is latched into this bit on SCLOCK if the Data Output Enable (MDE) bit is ‘0.’
3
I2CM
I
2C Master/Slave Mode Bit
Set by user to enable I2C software master mode.
Cleared by user to enable I
2C hardware slave mode.
2
I2CRS
I
2C Reset Bit (SLAVE MODE ONLY)
Set by user to reset the I2C interface.
Cleared by user code for normal I
2C operation.
1
I2CTX
I
2C Direction Transfer Bit (SLAVE MODE ONLY)
Set by the MicroConverter if the interface is transmitting.
Cleared by the MicroConverter if the interface is receiving.
0
I2CI
I
2C Interrupt Bit (SLAVE MODE ONLY)
Set by the MicroConverter after a byte has been transmitted or received.
Cleared automatically when user code reads the I2CDAT SFR (see I2CDAT below).
相關PDF資料 |
PDF描述 |
|---|---|
| RPS-1K-22-18/2.0-9 | HEAT SHRINK SLEEVE |
| EBM31DCMN | CONN EDGECARD 62POS .156 WW |
| REC5-243.3DRWZ/H/B | CONV DC/DC 5W 9-36VIN +/-3.3V |
| ADR06WARZ-R7 | IC VREF SERIES PREC 3V 8SOIC |
| EBM31DCMH | CONN EDGECARD 62POS .156 WW |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADUC831QS | 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk 制造商:Analog Devices 功能描述:KIT- ADUC831 DEV SYSTEM |
| EVAL-ADUC831QSZ | 功能描述:KIT DEV FOR ADUC831 QUICK START RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| EVAL-ADUC832QS | 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk 制造商:Analog Devices 功能描述:DEVELOPMENT KIT SYSTEM |
| EVAL-ADUC832QSZ | 功能描述:KIT DEV FOR ADUC832 QUICK START RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| EVAL-ADUC834QS | 制造商:Analog Devices 功能描述:DATA ACQ SYS, MICROCNVRTR, DUAL 16BIT/24BIT - ADCS W/ EMBEDD - Bulk 制造商:Analog Devices 功能描述:8052 ADUC834 QUICKSTART DEV KIT |
發布緊急采購，3分鐘左右您將得到回復。