參數資料
型號: BX80557E2140
廠商: INTEL CORP
元件分類: 微控制器/微處理器
英文描述: MICROPROCESSOR, PBGA775
封裝: LGA-775
文件頁數: 19/107頁
文件大?。?/td> 1474K
代理商: BX80557E2140
Datasheet
19
Electrical Specifications
2.6.2
DC Voltage and Current Specification
Table 5.
Voltage and Current Specifications
Symbol
Parameter
Min
Typ
Max
Unit Notes1, 2
NOTES:
1.
Unless otherwise noted, all specifications in this table are based on estimates and simulations or empirical data.
These specifications will be updated with characterized data from silicon measurements at a later date.
2.
Adherence to the voltage specifications for the processor are required to ensure reliable processor operation.
VID Range
VID
0.8500
1.5
V
3
3.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and can not be altered. Individual maximum VID values are calibrated during manufacturing such
that two processors at the same frequency may have different settings within the VID range. Note this differs
from the VID employed by the processor during a power management event (Thermal Monitor 2, Enhanced Intel
SpeedStep technology, or Extended HALT State).
VCC
Processor Number
E2200
E2180
E2160
E2140
VCC for
775_VR_CONFIG_06
2.2 GHz
2.0 GHz
1.8 GHz
1.6 GHz
Refer to Table 6 and
V
4, 5, 6
4.
These voltages are targets only. A variable voltage source should exist on systems in the event that a different
voltage is required. See Section 2.3 and Table 2 for more information.
5.
The voltage specification requirements are measured across VCC_SENSE and VSS_SENSE lands at the socket
with a 100 MHz bandwidth oscilloscope, 1.5 pF maximum probe capacitance, and 1 MΩ minimum impedance. The
maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from the system
is not coupled into the oscilloscope probe.
6.
Refer to Table 6 and Figure 1 for the minimum, typical, and maximum VCC allowed for a given current. The
processor should not be subjected to any VCC and ICC combination wherein VCC exceeds VCC_MAX for a given
current.
VCC_BOOT
Default VCC voltage for initial power up
1.10
V
VCCPLL
PLL VCC
- 5%
1.50
+ 5%
ICC
Processor Number
E2200
E2180
E2160
E2140
VCC for
775_VR_CONFIG_06
2.2 GHz
2.0 GHz
1.8 GHz
1.6 GHz
——
75
A
7
7.
ICC_MAX specification is based on the VCC_MAX loadline. Refer to Figure 1 for details.
VTT
FSB termination voltage
(DC + AC specifications)
1.14
1.20
1.26
V
8
8.
VTT must be provided via a separate voltage source and not be connected to VCC. This specification is measured
at the land.
VTT_OUT_LEFT and
VTT_OUT_RIGHT
ICC
DC Current that may be drawn from
VTT_OUT_LEFT and VTT_OUT_RIGHT per
pin
580
mA
9
9.
Baseboard bandwidth is limited to 20 MHz.
ITT
ICC for VTT supply before VCC stable
ICC for VTT supply after VCC stable
——
4.5
4.6
A
10
10.This is maximum total current drawn from VTT plane by only the processor. This specification does not include
the current coming from RTT (through the signal line). Refer to the Voltage Regulator-Down (VRD) 11.0 Processor
Power Delivery Design Guidelines For Desktop LGA775 Socket to determine the total ITT drawn by the system.
This parameter is based on design characterization and is not tested.
ICC_VCCPLL
ICC for PLL land
130
mA
ICC_GTLREF
ICC for GTLREF
200
μA
相關PDF資料
PDF描述
BXM80526B600128 64-BIT, 600 MHz, MICROPROCESSOR, PBGA495
BXM80526B700128 64-BIT, 700 MHz, MICROPROCESSOR, CPGA495
BXM80526B700 64-BIT, 700 MHz, MICROPROCESSOR, CPGA495
BXM80536GC2100F 32-BIT, 2100 MHz, MICROPROCESSOR, CPGA478
BXM80536GC1800F 32-BIT, 1800 MHz, MICROPROCESSOR, CPGA478
相關代理商/技術參數
參數描述
BX80557E2160 S LA8Z 制造商:Intel 功能描述:
BX80557E4400 制造商:Intel 功能描述:MPU Core?2 Duo Processor E4400 65nm 2GHz 775-Pin FCLGA6
BX80557E4500 S LA95 制造商:Intel 功能描述:MPU Core?2 Duo Processor E4500 65nm 2.2GHz 775-Pin FCLGA6
BX80557E4600 S LA94 制造商:Intel 功能描述:MPU Core?2 Duo Processor E4600 65nm 2.4GHz 775-Pin FCLGA6
BX80557E6300 制造商:Rochester Electronics LLC 功能描述: 制造商:Intel 功能描述: