參數資料
型號： (Z)PSD813F1
英文描述： Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM)
中文描述： Flash在系統可編程Mirocomputer外設（閃速，在系統可編程微控制器外圍器件，100萬位閃速存儲器，256K位的EEPROM，16K的位的SRAM）
文件頁數： 81/130頁
文件大小： 650K
代理商： (Z)PSD813F1
Prelimnary
PSD813F Famly
77
9.6.1 Standard JTAGSignals
The standard JTAG signals (TMS, TCK, TDI, and TDO) can be enabled by any of three
different conditions that are logically ORed. When enabled, TDI, TDO, TCK, and TMS are
inputs, waiting for a serial command from an external JTAG controller device (such as
FlashLink or Automated Test Equipment). When the enabling command is received from the
external JTAG controller, TDO becomes an output and the JTAG channel is fully functional
inside the PSD. The same command that enables the JTAG channel may optionally enable
the two additional JTAG pins, TSTAT and TERR.
The following symbolic logic equation specifies the conditions enabling the four basic
JTAG pins (TMS, TCK, TDI, and TDO) on their respective Port C pins. For purposes of
discussion, the logic label JTAG_ON will be used. When JTAG_ON is true, the four pins are
enabled for JTAG. When JTAG_ON is false, the four pins can be used for general PSD I/O.
JTAG_ON =
PSDsoft_enabled +
/* An NVM configuration bit inside the PSD is set by the designer
in the PSDsoft Configuration utility. This dedicates the pins for
JTAG at all times (compliant with IEEE 1149.1) */
Microcontroller_enabled +
/* The microcontroller can set a bit at run-time by writing to the
PSD register, JTAG Enable. This register is located at address
CSIOP + offset C7h. Setting the JTAG_ENABLE bit in this
register will enable the pins for JTAG use. This bit is cleared
by a PSD reset or the microcontroller. See Table 35 for bit
definition. */
PSD_product_term_enabled;
/* A dedicated product term (PT) inside the PSD can be used to
enable the JTAG pins. This PT has the reserved name
JTAGSEL. Once defined as a node in PSDabel, the designer
can write an equation for JTAGSEL. This method is used when
the Port C JTAG pins are multiplexed with other I/O signals.
It is recommended to logically tie the node JTAGSEL to the
JEN\ signal on the Flashlink cable when multiplexing JTAG
signals. See Application Note 54 for details.
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
*
*
*
*
*
*
*
JTAG_ENABLE
Table 35. JTAGEnable Register
JTAGEnable
*
Bits 1-7 are not used and should set to 0.
Bit definitions:
JTAG_ENABLE 1 = JTAG Port is Enabled.
0 = JTAG Port is Disabled.
The
PSD813F
Functional
Blocks
(cont.)
相關PDF資料
PDF描述
(Z)PSD813F3 Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，16K位SRAM)
(Z)PSD813F2(中文) Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位和256K位閃速存儲器，16K位SRAM)
(Z)PSD813F3R(中文) Multi-Chip-Module to Monolithic Flash PSD(閃速，在系統可編程微控制器外圍器件，0M位閃速存儲器，無SRAM)
(Z)PSD813F2 Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位和256K位閃速存儲器，16K位SRAM)
(Z)PSD813F3R Multi-Chip-Module to Monolithic Flash PSD(閃速，在系統可編程微控制器外圍器件，0M位閃速存儲器，無SRAM)
相關代理商/技術參數
參數描述
ZPSD813F1-12JI 制造商:WSI 功能描述:
ZPSD813F1-15J 制造商:WSI 功能描述:
ZPSD813F1-15U 制造商:WSI 功能描述:
ZPSD813F1-15UI 制造商:WSI 功能描述:
ZPSD813F1-90U 制造商:WSI 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*