- 您現在的位置：買賣IC網 > PDF目錄361795 > W83627SF W83627F plus Smart Card Reader Interface. VID Control. GP I/O? PDF資料下載
參數資料
| 型號： | W83627SF |
| 英文描述： | W83627F plus Smart Card Reader Interface. VID Control. GP I/O? |
| 中文描述： | W83627F加上智能卡閱讀器接口。 VID控制。大獎賽的I / O？ |
| 文件頁數： | 97/147頁 |
| 文件大?。?/td> | 1348K |
| 代理商： | W83627SF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁當前第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁
W83627SF
PRELIMINARY
Publication Release Date: Nov. 2000
Revision 0.60
- 90 -
configuration register is to be accessed. The designer can then access the desired configuration
register through the Extended Functions Data Register (I/O port address 2Fh or 4Fh).
After programming of the configuration register is finished, an additional value (AAh) should be written to
EFERs to exit the Extended Function mode to prevent unintentional access to those configuration
registers. The designer can also set bit 5 of CR26 (LOCKREG) to high to protect the configuration
registers against accidental accesses.
The configuration registers can be reset to their default or hardware settings only by a cold reset (pin MR
= 1). A warm reset will not affect the configuration registers.
9.1.2 Extended Functions Enable Registers (EFERs)
After a power-on reset, the W83627SF enters the default operating mode. Before the W83627SF enters
the extended function mode, a specific value must be programmed into the Extended Function Enable
Register (EFER) so that the extended function register can be accessed. The Extended Function
Enable Registers are write-only registers. On a PC/AT system, their port addresses are 2Eh or 4Eh (as
described in previous section).
9.1.3 Extended Function Index Registers (EFIRs), Extended Function Data Registers(EFDRs)
After the extended function mode is entered, the Extended Function Index Register (EFIR) must be
loaded with an index value (02h, 07h-FEh) to access Configuration Register 0 (CR0), Configuration
Register 7 (CR07) to Configuration Register FE (CRFE), and so forth through the Extended Function
Data Register (EFDR). The EFIRs are write-only registers with port address 2Eh or 4Eh (as described in
section 12.2.1) on PC/AT systems; the EFDRs are read/write registers with port address 2Fh or 4Fh (as
described in section 9.2.1) on PC/AT systems.
9.2 Configuration Sequence
To program W83627SF configuration registers, the following configuration sequence must be followed:
(1). Enter the extended function mode
(2). Configure the configuration registers
(3). Exit the extended function mode
9.2.1 Enter the extended function mode
To place the chip into the extended function mode, two successive wrtites of 0x87 must be applied to
Extended Function Enable Registers(EFERs, i.e. 2Eh or 4Eh).
相關PDF資料 |
PDF描述 |
|---|---|
| W83697UF | W83697F plus 2 Extra UART (total 4 UART) |
| W83777F | Peripheral IC |
| W83877AD | Peripheral (Multifunction) Controller |
| W83877AF | Peripheral (Multifunction) Controller |
| W83910F | IPMI BMC plus H/W Monitor. UART. 5-sets Master/Slave SMBus. for Server PC Application |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W83627SF_05 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O |
| W83627SF-AW | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O |
| W83627SF-PW | 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O |
| W83627SG-AW | 功能描述:IC LPC SUPER I/O 128-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:* 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| W83627THF | 制造商:Nuvoton Technology Corp 功能描述:I/O Controller LPC Controller 128-Pin PQFP |
發布緊急采購，3分鐘左右您將得到回復。