參數資料
型號： W83627SF
英文描述： W83627F plus Smart Card Reader Interface. VID Control. GP I/O?
中文描述： W83627F加上智能卡閱讀器接口。 VID控制。大獎賽的I / O？
文件頁數： 84/147頁
文件大?。?/td> 1348K
代理商： W83627SF
W83627SF
PRELIMINARY
Publication Release Date: Nov. 2000
Revision 0.60
- 77 -
6.3.13 ECP Operation
The host must negotiate on the parallel port to determine if the peripheral supports the ECP protocol
before ECP operation. After negotiation, it is necessary to initialize some of the port bits. The following
are required:
(a) Set direction = 0, enabling the drivers.
(b) Set strobe = 0, causing the nStrobe signal to default to the deasserted state.
(c) Set autoFd = 0, causing the nAutoFd signal to default to the deasserted state.
(d) Set mode = 011 (ECP Mode)
ECP address/RLE bytes or data bytes may be sent automatically by writing the ecpAFifo or ecpDFifo,
respectively.
6.3.13.1 Mode Switching
Software will execute P1284 negotiation and all operation prior to a data transfer phase under
programmed I/O control (mode 000 or 001). Hardware provides an automatic control line handshake,
moving data between the FIFO and the ECP port only in the data transfer phase (mode 011 or 010).
If the port is in mode 000 or 001 it may switch to any other mode. If the port is not in mode 000 or 001 it
can only be switched into mode 000 or 001. The direction can be changed only in mode 001.
When in extended forward mode, the software should wait for the FIFO to be empty before switching
back to mode 000 or 001. In ECP reverse mode the software waits for all the data to be read from the
FIFO before changing back to mode 000 or 001.
6.3.13.2 Command/Data
ECP mode allows the transfer of normal 8-bit data or 8-bit commands. In the forward direction, normal
data are transferred when HostAck is high and an 8-bit command is transferred when HostAck is low.
The most significant bits of the command indicate whether it is a run-length count (for compression) or a
channel address.
In the reverse direction, normal data are transferred when PeriphAck is high and an 8bit command is
transferred when PeriphAck is low. The most significant bit of the command is always zero.
6.3.13.3 Data Compression
The W83627SF supports run length encoded (RLE) decompression in hardware and can transfer
compressed data to a peripheral. Note that the odd (RLE) compression in hardware is not supported. In
order to transfer data in ECP mode, the compression count is written to the ecpAFifo and the data byte
is written to the ecpDFifo.
6.3.14 FIFO Operation
The FIFO threshold is set in configuration register 5. All data transfers to or from the parallel port can
proceed in DMA or Programmed I/O (non-DMA) mode, as indicated by the selected mode. The FIFO is
used by selecting the Parallel Port FIFO mode or ECP Parallel Port Mode. After a reset, the FIFO is
disabled.
相關PDF資料
PDF描述
W83697UF W83697F plus 2 Extra UART (total 4 UART)
W83777F Peripheral IC
W83877AD Peripheral (Multifunction) Controller
W83877AF Peripheral (Multifunction) Controller
W83910F IPMI BMC plus H/W Monitor. UART. 5-sets Master/Slave SMBus. for Server PC Application
相關代理商/技術參數
參數描述
W83627SF_05 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O
W83627SF-AW 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O
W83627SF-PW 制造商:WINBOND 制造商全稱:Winbond 功能描述:WINBOND I/O
W83627SG-AW 功能描述:IC LPC SUPER I/O 128-PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:* 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
W83627THF 制造商:Nuvoton Technology Corp 功能描述:I/O Controller LPC Controller 128-Pin PQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*