- 您現在的位置：買賣IC網 > PDF目錄68746 > W25Q80BWZPIP (WINBOND ELECTRONICS CORP) 8M X 1 SPI BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | W25Q80BWZPIP |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 8M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 6 X 5 MM, GREEN , PLASTIC, WSON-8 |
| 文件頁數： | 36/71頁 |
| 文件大小： | 0K |
| 代理商： | W25Q80BWZPIP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
W25Q80BW
Publication Release Date: January 26, 2011
- 41 -
Preliminary - Revision A
8.2.24 32KB Block Erase (52h)
The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of all
1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “52h” followed a 24-bit block address (A23-A0) (see Figure 2). The Block
Erase instruction sequence is shown in figure 22.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of
the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Block Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase
instruction will not be executed if the addressed page is protected by the Block Protect (CMP, SEC, TB,
BP2, BP1, and BP0) bits (see Status Register Memory Protection table).
Figure 22. 32KB Block Erase Instruction Sequence Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| W25Q80VZPI | 1M X 8 SPI BUS SERIAL EEPROM, DSO8 |
| W26B041H70LI | 256K X 16 STANDARD SRAM, 70 ns, PDSO44 |
| W26B04B-70LE | 256K X 16 STANDARD SRAM, 70 ns, PBGA48 |
| W29L102Q-20B | 64K X 16 FLASH 3.3V PROM, 200 ns, PDSO40 |
| W33D2011 | LIQUID CRYSTAL DISPLAY DRIVER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25S243A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM |
| W25S243A-12 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM |
| W25S243AD-12 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM |
| W25S243AF-12 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM |
| W25X10 | 制造商:WINBOND 制造商全稱:Winbond 功能描述:The W25X10 (1M-bit), W25X20 (2M-bit), W25X40 (4M-bit) and W25X80 (8M-bit) Serial Flash memories provide a storage solution for systems with limited space, pins and power. |
發布緊急采購，3分鐘左右您將得到回復。