參數資料
型號： W25Q80BWZPIP
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 8M X 1 SPI BUS SERIAL EEPROM, PDSO8
封裝： 6 X 5 MM, GREEN , PLASTIC, WSON-8
文件頁數： 15/71頁
文件大小： 0K
代理商： W25Q80BWZPIP
W25Q80BW
- 22 -
8.2.8
Read Status Register-1 (05h) and Read Status Register-2 (35h)
The Read Status Register instructions allow the 8-bit Status Registers to be read. The instruction is
entered by driving /CS low and shifting the instruction code “05h” for Status Register-1 or “35h” for
Status Register-2 into the DI pin on the rising edge of CLK. The status register bits are then shifted out on
the DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in figure 7. The Status
Register bits are shown in figure 3a and 3b and include the BUSY, WEL, BP2-BP0, TB, SEC, SRP0,
SRP1, QE, LB3-0, CMP and SUS bits (see Status Register section earlier in this datasheet).
The Read Status Register instruction may be used at any time, even while a Program, Erase or Write
Status Register cycle is in progress. This allows the BUSY status bit to be checked to determine when
the cycle is complete and if the device can accept another instruction. The Status Register can be read
continuously, as shown in Figure 7. The instruction is completed by driving /CS high.
Figure 7. Read Status Register Instruction Sequence Diagram
8.2.9
Write Status Register (01h)
The Write Status Register instruction allows the Status Register to be written. Only non-volatile Status
Register bits SRP0, SEC, TB, BP2, BP1, BP0 (bits 7 thru 2 of Status Register-1) and CMP, LB3, LB2,
LB1, LB0, QE, SRP1 (bits 14 thru 8 of Status Register-2) can be written to. All other Status Register bit
locations are read-only and will not be affected by the Write Status Register instruction. LB3-0 are non-
volatile OTP bits, once it is set to 1, it can not be cleared to 0. The Status Register bits are shown in
figure 3a and 3b and described in 8.1.
To write non-volatile Status Register bits, a standard Write Enable (06h) instruction must previously have
been executed for the device to accept the Write Status Register Instruction (Status Register bit WEL
must equal 1). Once write enabled, the instruction is entered by driving /CS low, sending the instruction
code “01h”, and then writing the status register data byte as illustrated in figure 8.
To write volatile Status Register bits, a Write Enable for Volatile Status Register (50h) instruction must
have been executed prior to the Write Status Register instruction (Status Register bit WEL remains 0).
However, SRP1 and LB3, LB2, LB1, LB0 can not be changed from “1” to “0” because of the OTP
protection for these bits. Upon power off, the volatile Status Register bit values will be lost, and the non-
volatile Status Register bit values will be restored when power on again.
相關PDF資料
PDF描述
W25Q80VZPI 1M X 8 SPI BUS SERIAL EEPROM, DSO8
W26B041H70LI 256K X 16 STANDARD SRAM, 70 ns, PDSO44
W26B04B-70LE 256K X 16 STANDARD SRAM, 70 ns, PBGA48
W29L102Q-20B 64K X 16 FLASH 3.3V PROM, 200 ns, PDSO40
W33D2011 LIQUID CRYSTAL DISPLAY DRIVER, PQFP64
相關代理商/技術參數
參數描述
W25S243A 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
W25S243A-12 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
W25S243AD-12 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
W25S243AF-12 制造商:WINBOND 制造商全稱:Winbond 功能描述:64K X 64 BURST PIPELINED HIGH-SPEED CMOS STATIC RAM
W25X10 制造商:WINBOND 制造商全稱:Winbond 功能描述:The W25X10 (1M-bit), W25X20 (2M-bit), W25X40 (4M-bit) and W25X80 (8M-bit) Serial Flash memories provide a storage solution for systems with limited space, pins and power.
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*