- 您現在的位置：買賣IC網 > PDF目錄382723 > UJA1065 (NXP Semiconductors N.V.) High-speed CAN/LIN fail-safe system basis chip PDF資料下載
參數資料
| 型號： | UJA1065 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | High-speed CAN/LIN fail-safe system basis chip |
| 中文描述： | 高速的CAN / LIN故障防護系統基礎芯片 |
| 文件頁數： | 17/67頁 |
| 文件大小： | 285K |
| 代理商： | UJA1065 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
9397 750 14409
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Objective data sheet
Rev. 01 — 10 August 2005
17 of 67
Philips Semiconductors
UJA1065
High-speed CAN/LIN fail-safe system basis chip
The SBC also detects if pin RSTN is clamped HIGH. If the HIGH-level remains on the pin
for longer than t
RSTN(ext)
while pin RSTN is driven internally to a LOW-level by the SBC,
the SBC falls back immediately to Fail-safe mode since the microcontroller cannot be
reset any more. By entering Fail-safe mode, the V1 voltage regulator shuts down and the
microcontroller stops.
Additionally, chattering reset signals are handled by the SBC in such a way that the
system safely falls back to Fail-safe mode with the lowest possible power consumption.
6.5.2
EN output
Pin EN can be used to control external hardware such as power components or as a
general purpose output if the system is running properly. During all reset events, when pin
RSTN is pulled LOW, the EN control bit will be cleared, pin EN will be pulled LOW and will
stay LOW after pin RSTN is released. In Normal mode and Flash mode of the SBC, the
microcontroller can set the EN control bit via the SPI. This results in releasing pin EN
which then returns to a HIGH-level.
6.6 Power supplies
6.6.1
BAT14, BAT42 and SYSINH
The SBC has two supply pins, pin BAT42 and pin BAT14. Pin BAT42 supplies most of the
SBC where pin BAT14 only supplies the linear voltage regulators and the INH/LIMP output
pin. This supply architecture allows different supply strategies including the use of
external DC-to-DC converters controlled by the pin SYSINH.
6.6.2
SENSE input
The SBC has a dedicated SENSE pin for dynamic monitoring of the battery contact of an
electronic control unit. Connecting this pin in front of the polarity protection diode of the
ECU provides an early warning if the battery becomes disconnected.
6.6.3
Voltage regulators V1 and V2
The UJA1065 has two independent voltage regulators supplied out of the BAT14 pin.
Regulator V1 is intended to supply the microcontroller. Regulator V2 is reserved for the
high-speed CAN transceiver.
6.6.3.1
Voltage regulator V1
The V1 voltage is continuously monitored to provide the system reset signal when
undervoltage situations occur. Whenever the V1 voltage falls below one of the three
programmable thresholds, a hardware reset is forced.
A dedicated V1 supply comparator (V1 Monitor) observes V1 for undervoltage events
lower than V
UV(VF1)
. This allows the application to receive a supply warning interrupt in
case one of the lower V1 undervoltage reset thresholds is selected.
The V1 regulator is overload protected. The maximum output current available from pin
V1 depends on the voltage applied to pin BAT14 according to the characteristics section.
For thermal reasons, the total power dissipation should be taken into account.
相關PDF資料 |
PDF描述 |
|---|---|
| UL631H256 | SimtekLow Voltage SoftStore 32K x 8 nvSRAM |
| UL631H256S2C35 | SimtekLow Voltage SoftStore 32K x 8 nvSRAM |
| UL631H256S2C35G1 | SimtekLow Voltage SoftStore 32K x 8 nvSRAM |
| UL631H256S2C45 | SimtekLow Voltage SoftStore 32K x 8 nvSRAM |
| UL631H256S2K35 | SimtekLow Voltage SoftStore 32K x 8 nvSRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UJA1065TW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:High-speed CAN/LIN fail-safe system basis chip |
| UJA1065TW/3V0 | 功能描述:網絡控制器與處理器 IC HI SPEED CAN SYSTEM RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| UJA1065TW/3V0,512 | 功能描述:CAN 接口集成電路 HI SPEED CAN SYSTEM RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| UJA1065TW/3V0,518 | 功能描述:網絡控制器與處理器 IC HI SPEED CAN SYSTEM RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| UJA1065TW/3V0512 | 制造商:NXP Semiconductors 功能描述:CONTROLLER SYS CAN/LIN 3V 32HTSSOP |
發布緊急采購，3分鐘左右您將得到回復。