ELECTRICAL CHARACTERISTICS
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
over recommended operating free-air temperature range, T version (unless otherwise noted)
(1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Vhys
Input hysteresis
0.15
V
All inputs(2) except
–0.3
0.8
OSCIN
VIL
Low-level input voltage
V
OSCIN only
–0.3
0.35 VCC
All inputs except
2
VCCIO + 0.3
OSCIN
VIH
High-level input voltage
V
OSCIN only
0.65 VCC
VCC + 0.3
Vth
Input threshold voltage
AWD only
1.35
1.8
V
Drain-to-source on
RDSON
AWD only(3)
VOL = 0.35 V at IOL = 2 mA
175
resistance
IOL = IOL MAX
0.2 VCCIO
VOL
Low-level output voltage(4)
V
IOL = 50 A
0.2
IOH = IOH MIN
0.8 VCCIO
VOH
High-level output voltage(4)
V
IOH = 50 A
VCCIO – 0.2
VI < VSSIO – 0.3 or
IIC
Input clamp current (I/O pins)(5)
–2
2
mA
VI > VCCIO + 0.3
IIL Pulldown
VI = VSS
–1
1
IIH Pulldown
VI = VCCIO
5
40
II
Input current (I/O pins)
IIL Pullup
VI = VSS
–40
–5
A
IIH Pullup
VI = VCCIO
–1
1
All other pins
No pullup or pulldown
–1
1
CLKOUT, TDO
8
RST, SPInCLK,
SPInSOMI,
4
IOL
Low-level output current
VOL = VOL MAX
mA
SPInSIMO(6)
All other output
2
pins(7)
CLKOUT, TDO
–8
RST, SPInCLK,
SPInSOMI,
–4
IOH
High-level output current
VOH = VOH MIN
mA
SPInSIMO(6)
All other output
–2
pins except RST(7)
SYSCLK = 60 MHz,
135
mA
ICLK = 20 MHz, VCC = 2.05 V
VCC Digital supply current (operating mode)
SYSCLK = 24 MHz,
105
mA
ICC
ICLK = 12 MHz, VCC = 2.05 V
VCC Digital supply current (standby mode)
(8)
OSCIN = 6 MHz, VCC = 2.05 V
4
mA
VCC Digital supply current (halt mode)
(8)
All frequencies, VCC = 2.05 V
2
mA
VCCIO Digital supply current (operating mode)
No DC load, VCCIO = 3.6 V
(8)
10
mA
ICCIO
VCCIO Digital supply current (standby mode)
No DC load, VCCIO = 3.6 V
(8)
300
A
VCCIO Digital supply current (halt mode)
No DC load, VCCIO = 3.6 V
(8)
300
A
(1)
Source currents (out of the device) are negative while sink currents (into the device) are positive.
(2)
This does not apply to the PORRST pin. For PORRST exceptions, see the RST and PORRST timings section.
(3)
These values help to determine the external RC network circuit. For more details, see the TMS470R1x System Module Reference Guide
(literature number SPNU189).
(4)
VOL and VOH are linear with respect to the amount of load current (IOL/IOH) applied.
(5)
Parameter does not apply to input-only or output-only pins.
(6)
n = 1–5.
(7)
The 2-mA buffers on this device are called zero-dominant buffers. If two of these buffers are shorted together and one is outputting a
low level and the other is outputting a high level, the resulting value is always low.
(8)
I/O pins configured as inputs or outputs with no load. All pulldown inputs
≤ 0.2 V. All pullup inputs ≥ VCCIO – 0.2 V.
Copyright 2005–2008, Texas Instruments Incorporated
25