參數資料
型號： TDA8035HN/C1
廠商： NXP SEMICONDUCTORS
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PQCC32
封裝： 5 X 5 MM, 0.85 MM HEIGHT, PLASTIC, SOT617-7, HVQFN-32
文件頁數： 19/32頁
文件大?。?/td> 908K
代理商： TDA8035HN/C1
TDA8035HN
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 1.0 — 19 April 2011
26 of 32
NXP Semiconductors
TDA8035HN
Smart card interface
14. Soldering
14.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
14.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250
°C. The top-surface temperature
of the packages should preferable be kept below 220
°C for thick/large packages, and
below 235
°C small/thin packages.
14.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
parallel to the transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45° angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
相關PDF資料
PDF描述
TDA8779H-T SPECIALTY ANALOG CIRCUIT, PQFP44
TEA1103N 0.014 A BATTERY CHARGE CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDIP20
TEA1103TD 0.014 A BATTERY CHARGE CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO20
TEA1610T/N5,118 SWITCHING CONTROLLER, 550 kHz SWITCHING FREQ-MAX, PDSO16
TEA1733LT/N1 SWITCHING CONTROLLER, 71 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
TDA8037T/C1J 制造商:NXP Semiconductors 功能描述:TDA8037T/SO28/REEL13//C1 - Tape and Reel
TDA8037TT/C1J 制造商:NXP Semiconductors 功能描述:TDA8037TT/TSSOP16/REEL13//C1 - Tape and Reel
TDA8040T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quadrature demodulator
TDA8041H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quadrature demodulator controller
TDA8041HB-S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ASK/FSK Demodulator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*