參數資料
型號： SP37E760-MC
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 外設及接口
英文描述： 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
中文描述： MULTIFUNCTION PERIPHERAL, PQFP100
封裝： QFP-100
文件頁數： 34/78頁
文件大?。?/td> 510K
代理商： SP37E760-MC
SMSC DS – SP37E760
Page 34
Rev. 04/13/2001
5.4.2
This specification describes the standard ISA interface to the Extended Capabilities Port (ECP). All ISA devices
supporting ECP must meet the requirements contained in this section or the port will not be supported by Microsoft.
For a description of the ECP Protocol, please refer to the IEEE 1284 Extended Capabilities Port Protocol and ISA
Interface Standard, Rev. 1.09, Jan.7, 1993. This document is available from Microsoft.
ISA IMPLEMENTATION STANDARD
5.4.3
The port is software and hardware compatible with existing parallel ports so that it may be used as a standard LPT
port if ECP is not required. The port is designed to be simple and requires a small number of gates to implement. It
does not do any “protocol” negotiation, rather it provides an automatic high burst-bandwidth channel that supports
DMA for ECP in both the forward and reverse directions.
Small FIFOs are employed in both forward and reverse directions to smooth data flow and improve the maximum
bandwidth requirement. The size of the FIFO is 16 bytes deep. The port supports an automatic handshake for the
standard parallel port to improve compatibility mode transfer speed.
The port also supports run length encoded (RLE) decompression (required) in hardware. Compression is
accomplished by counting identical bytes and transmitting an RLE byte that indicates how many times the next byte is
to be repeated. Decompression simply intercepts the RLE byte and repeats the following byte the specified number of
times. Hardware support for compression is optional.
Table 17 - ECP Pin Descriptions
NAME
TYPE
nStrobe
O
During write operations nStrobe registers data or address into the slave on
the asserting edge (handshakes with Busy).
Pdata 7:0
I/O
Contains address or data or RLE data.
Nack
I
Indicates valid data driven by the peripheral when asserted. This signal
handshakes with nAutoFd in reverse.
PeriphAck (Busy)
I
This signal deasserts to indicate that the peripheral can accept data. This
signal handshakes with nStrobe in the forward direction. In the reverse
direction this signal indicates whether the data lines contain ECP command
information or data. The peripheral uses this signal to flow control in the
forward direction. It is an “interlocked” handshake with nStrobe. PeriphAck
also provides command information in the reverse direction.
Perror
(nAckReverse)
forward). The peripheral drives this signal low to acknowledge
nReverseRequest. It is an “interlocked” handshake with nReverseRequest.
The host relies upon nAckReverse to determine when it is permitted to
drive the data bus.
Select
I
Indicates printer on line.
NAutoFd
(HostAck)
with nAck in the reverse direction. In the forward direction this signal
indicates whether the data lines contain ECP address or data. The host
drives this signal to flow control in the reverse direction. It is an “interlocked”
handshake with nAck. HostAck also provides command information in the
forward phase.
NFault
(nPeriphRequest)
mechanism for peer-to-peer communication. This signal is valid only in the
forward direction. During ECP Mode the peripheral is permitted (but not
required) to drive this pin low to request a reverse transfer. The request is
merely a “hint” to the host; the host has ultimate control over the transfer
direction. This signal would be typically used to generate an interrupt to the
host CPU.
NInit
O
Sets the transfer direction (asserted = reverse, deasserted = forward). This
pin is driven low to place the channel in the reverse direction. The
peripheral is only allowed to drive the bi-directional data bus while in ECP
Mode and HostAck is low and nSelectIn is high.
NSelectIn
O
Always deasserted in ECP mode.
DESCRIPTION
DESCRIPTION
I
Used to acknowledge a change in the direction the transfer (asserted =
O
Requests a byte of data from the peripheral when asserted, handshaking
I
Generates an error interrupt when asserted. This signal provides a
相關PDF資料
PDF描述
SP8720 ECL two-modulus divider, with ECL10K compatible outputs
SP8720ADG ECL two-modulus divider, with ECL10K compatible outputs
SP8720BDG ECL two-modulus divider, with ECL10K compatible outputs
SPF5001 Surface-mount 4-circuit Low-side Switch Array
SPF5002 Surface-mount 4-circuit Low-side Switch Array
相關代理商/技術參數
參數描述
SP37E760-MD 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
SP37E760-MT 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
SP37R0FL 制造商:TE Connectivity 功能描述:SP3 7R0 1% LOOSEFixed Resistor
SP38 制造商:BES 功能描述:3/8" x 6" Spade Bit 制造商:BES MANUFACTURING 功能描述:SPADE BIT 3/8 X 6 INCH
SP380 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NOR GATES
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*