參數資料
型號: SP37E760-MC
廠商: STANDARD MICROSYSTEMS CORP
元件分類: 外設及接口
英文描述: 3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS
中文描述: MULTIFUNCTION PERIPHERAL, PQFP100
封裝: QFP-100
文件頁數: 16/78頁
文件大小: 510K
代理商: SP37E760-MC
4.1.3.1
The ERDAI bit enables the Received Data Available Interrupt (and time-out interrupts in the FIFO mode) when set to
logic “1”.
4.1.3.2
ETHREI, Bit 1
The ETHREI bit enables the Transmitter Holding Register Empty Interrupt when set to logic “1”.
4.1.3.3
ELSI, Bit 2
The ELSI bit enables the Received Line Status Interrupt when set to logic “1”. The error sources causing the interrupt
are Overrun, Parity, Framing and Break. The Line Status Register must be read to determine the source.
4.1.3.4
EMSI, Bit 3
The EMSI bit enables the MODEM Status Interrupt when set to logic “1”. An MSI is caused when one of the Modem
Status Register bits changes state.
4.1.3.5
Reserved, Bits 4 - 7
Bits 4 to 7 are
RESERVED
. Reserved bits cannot be written and return 0 when read.
SMSC DS – SP37E760
Page 16
Rev. 04/13/2001
ERDAI, Bit 0
4.1.4
By accessing the Interrupt Identification register (Address Offset = 2H, DLAB = X, READ), the host CPU can
determine the highest priority interrupt and its source. Four levels of interrupt priority exist. They are in descending
order of priority:
INTERRUPT IDENTIFICATION REGISTER (IIR)
1. Receiver Line Status (highest priority)
2. Received Data Ready
3. Transmitter Holding Register Empty
4. MODEM Status (lowest priority)
Information indicating that a prioritized interrupt is pending and the source of that interrupt is stored in the Interrupt
Identification Register (refer to the Interrupt Control Table, Table 5). When the CPU accesses the IIR, the Serial Port
freezes all interrupts and indicates the highest priority pending interrupt to the CPU. During this CPU access, even if
the Serial Port records new interrupts, the current indication does not change until access is completed.
4.1.4.1
Interrupt Pending, Bit 0
The Interrupt Pending bit can be used in either a hardwired prioritized or polled environment to indicate whether an
interrupt is pending. When bit 0 is a logic “0”, an interrupt is pending and the contents of the IIR may be used as a
pointer to the appropriate internal service routine. When bit 0 is a logic “1”, no interrupt is pending.
4.1.4.2
Interrupt ID, Bits 1 - 2
The Interrupt ID bits of the IIR are used to identify the highest priority interrupt pending as indicated by the Interrupt
Control Table (Table 5).
4.1.4.3
Time-Out, Bit 3
In non-FIFO mode, the Time-Out bit is a logic “0”. In FIFO mode the Time-Out bit is set along with bit 2 when a time-
out interrupt is pending.
4.1.4.4
Reserved, Bits 4 - 5
Bits 4 to 5 are
RESERVED
. Reserved bits cannot be written and return 0 when read.
4.1.4.5
FIFOs Enabled, Bits 6 - 7
The FIFOs Enabled bits are set when the FIFO CONTROL Register bit 0 equals 1.
相關PDF資料
PDF描述
SP8720 ECL two-modulus divider, with ECL10K compatible outputs
SP8720ADG ECL two-modulus divider, with ECL10K compatible outputs
SP8720BDG ECL two-modulus divider, with ECL10K compatible outputs
SPF5001 Surface-mount 4-circuit Low-side Switch Array
SPF5002 Surface-mount 4-circuit Low-side Switch Array
相關代理商/技術參數
參數描述
SP37E760-MD 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
SP37E760-MT 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
SP37R0FL 制造商:TE Connectivity 功能描述:SP3 7R0 1% LOOSEFixed Resistor
SP38 制造商:BES 功能描述:3/8" x 6" Spade Bit 制造商:BES MANUFACTURING 功能描述:SPADE BIT 3/8 X 6 INCH
SP380 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NOR GATES