- 您現在的位置：買賣IC網 > PDF目錄365432 > S71GL512NB0 (Spansion Inc.) Stacked Multi-chip Product (MCP) PDF資料下載
參數資料
| 型號： | S71GL512NB0 |
| 廠商： | Spansion Inc. |
| 英文描述： | Stacked Multi-chip Product (MCP) |
| 中文描述： | 堆疊式多芯片產品（MCP） |
| 文件頁數： | 62/147頁 |
| 文件大?。?/td> | 1655K |
| 代理商： | S71GL512NB0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁
62
S29GLxxxN MirrorBit
TM
Flash Family
S29GLxxxN_00_A4 June 14, 2004
A d v a n c e I n f o r m a t i o n
Reads and writes from the main memory are allowed.
PPB Lock Bit Set Command
The PPB Lock Bit Set command is used to set the PPB Lock Bit to the “freeze state”
if it is cleared either at reset or if the Password Unlock command was successfully
executed. There is no PPB Lock Bit Clear command. Once the PPB Lock Bit is set
to the “freeze state”, it cannot be cleared unless the device is taken through a
power-on clear (for Persistent Protection Mode) or the Password Unlock command
is executed (for Password Protection Mode). If the Password Protection Mode Lock
Bit is programmed, the PPB Lock Bit status is reflected as set to the “freeze state”,
even after a power-on reset cycle.
PPB Lock Bit Status Read Command
The programming state of the PPB Lock Bit can be verified by executing a PPB
Lock Bit Status Read command to the device.
The
Global Volatile Sector Protection Freeze Command Set Exit
command
must be issued after the execution of the commands listed previously to reset the
device to read mode.
Volatile Sector Protection Command Set
The Volatile Sector Protection Command Set permits the user to set the Dynamic
Protection Bit (DYB) to the “protected state”, clear the Dynamic Protection Bit
(DYB) to the “unprotected state”, and read the logic state of the Dynamic Protec-
tion Bit (DYB).
The
Volatile Sector Protection Command Set Entry
command sequence
must be issued prior to any of the commands listed following to enable proper
command execution.
Note that issuing the
Volatile Sector Protection Command Set Entry
com-
mand
disables reads for the bank selected with the command
.
Reads and
Writes for other banks excluding that bank are allowed
.
DYB Set Command
DYB Clear Command
The DYB Set and DYB Clear commands are used to protect or unprotect a DYB for
a given sector. The high order address bits are issued at the same time as the
code 00h or 01h on DQ7-DQ0. All other DQ data bus pins are ignored during the
data write cycle. The DYB bits are modifiable at any time, regardless of the state
of the PPB bit or PPB Lock Bit. The DYB bits are cleared to the “unprotected state”
at power-up or hardware reset.
—DYB Status Read Command
The programming state of the DYB bit for a given sector can be verified by writing
a DYB Status Read command to the device. This requires an initial access delay.
The
Volatile Sector Protection Command Set Exit
command must be issued
after the execution of the commands listed previously to reset the device to read
mode.
Note that issuing the
Volatile Sector Protection Command Set Exit com-
mand re-enables reads and writes to the main memory
.
Secured Silicon Sector Entry Command
The Secured Silicon Sector Entry command allows the following commands to be
executed
相關PDF資料 |
PDF描述 |
|---|---|
| S71GS256NC0BFWAK0 | 128N based MCPs |
| S71GS128NB0 | 128N based MCPs |
| S71GS128NB0BAWAK0 | 128N based MCPs |
| S71GS128NB0BAWAK2 | 128N based MCPs |
| S71GS128NB0BAWAK3 | 128N based MCPs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71GL512NC0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP) |
| S71GL-N | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL-N_08 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GLXXXNC0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP) |
| S71GS128NB0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:128N based MCPs |
發布緊急采購，3分鐘左右您將得到回復。