參數資料
型號： S71GL512NB0
廠商： Spansion Inc.
英文描述： Stacked Multi-chip Product (MCP)
中文描述： 堆疊式多芯片產品（MCP）
文件頁數： 45/147頁
文件大小： 1655K
代理商： S71GL512NB0
June 14, 2004 S29GLxxxN_00_A4
S29GLxxxN MirrorBit
TM
Flash Family
45
A d v a n c e I n f o r m a t i o n
shipped from the factory with the Secured Silicon Sector permanently locked.
Contact your sales representative for details on using the ExpressFlash service.
Write Protect (WP#)
The Write Protect function provides a hardware method of protecting the first or
last sector group without using V
ID
. Write Protect is one of two functions provided
by the WP#/ACC input.
If the system asserts V
IL
on the WP#/ACC pin, the device disables program and
erase functions in the first or last sector group independently of whether those
sector groups were protected or unprotected using the method described in“Ad-
vanced Sector Protection” section on page 38. Note that if WP#/ACC is at V
IL
when the device is in the standby mode, the maximum input load current is in-
creased. See the table in “DC Characteristics” section on page 78.
If the system asserts V
IH
on the WP#/ACC pin, the device reverts to
whether the first or last sector was previously set to be protected or un-
protected using the method described in “Sector Group Protection and
Unprotection”.
Note that WP# has an internal pullup; when uncon-
nected, WP# is at V
IH
.
Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing
provides data protection against inadvertent writes (refer to Tables
16
and
17
for
command definitions). In addition, the following hardware data protection mea-
sures prevent accidental erasure or programming, which might otherwise be
caused by spurious system level signals during V
CC
power-up and power-down
transitions, or from system noise.
Low V
CC
Write Inhibit
When V
CC
is less than V
LKO
, the device does not accept any write cycles. This pro-
tects data during V
CC
power-up and power-down. The command register and all
internal program/erase circuits are disabled, and the device resets to the read
mode. Subsequent writes are ignored until V
CC
is greater than V
LKO
. The system
must provide the proper signals to the control pins to prevent unintentional writes
when V
CC
is greater than V
LKO
.
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write
cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# = V
IL
, CE# = V
IH
or WE# =
V
IH
. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a
logical one.
Power-Up Write Inhibit
If WE# = CE# = V
IL
and OE# = V
IH
during power up, the device does not accept
commands on the rising edge of WE#. The internal state machine is automatically
reset to the read mode on power-up.
Common Flash Memory Interface (CFI)
相關PDF資料
PDF描述
S71GS256NC0BFWAK0 128N based MCPs
S71GS128NB0 128N based MCPs
S71GS128NB0BAWAK0 128N based MCPs
S71GS128NB0BAWAK2 128N based MCPs
S71GS128NB0BAWAK3 128N based MCPs
相關代理商/技術參數
參數描述
S71GL512NC0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP)
S71GL-N 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM
S71GL-N_08 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM
S71GLXXXNC0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP)
S71GS128NB0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:128N based MCPs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*