- 您現在的位置：買賣IC網 > PDF目錄370013 > PowerPC 750 (IBM Microeletronics) 32-Bit Embedded Microprocessor(32位精簡指令集嵌入式微處理器) PDF資料下載
參數資料
| 型號： | PowerPC 750 |
| 廠商： | IBM Microeletronics |
| 英文描述： | 32-Bit Embedded Microprocessor(32位精簡指令集嵌入式微處理器) |
| 中文描述： | 32位嵌入式微處理器（32位精簡指令集嵌入式微處理器） |
| 文件頁數： | 40/46頁 |
| 文件大?。?/td> | 610K |
| 代理商： | POWERPC 750 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Page 36
Version 2.0
Datasheet
9/30/99
PowerPC 750 SCM RISC Microprocessor
PID8p-750
Preliminary Copy
Internal Package Conduction Resistance
For the exposed-die packaging technology, shown in Table “Package Thermal Characteristics,” on page 7,
the intrinsic conduction thermal resistance paths are as follows.
Die junction-to-case thermal resistance
Die junction-to-lead thermal resistance
Figure 19 depicts the primary heat transfer path for a package with an attached heat sink mounted to a
printed-circuit board.
Heat generated on the active side (ball) of the chip is conducted through the silicon, then through the heat
sink attach material (or thermal interface material), and finally to the heat sink; where it is removed by forced-
air convection. Since the silicon thermal resistance is quite small, for a first-order analysis, the temperature
drop in the silicon may be neglected. Thus, the heat sink attach material and the heat sink conduction/con-
vective thermal resistances are the dominant terms.
Adhesives and Thermal Interface Materials
A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the thermal
contact resistance. For those applications where the heat sink is attached by a spring clip mechanism,
Figure 20 shows the thermal performance of three thin-sheet thermal-interface materials (silicon, graphite/oil,
floroether oil), a bare joint, and a joint with thermal grease, as a function of contact pressure. As shown, the
performance of these thermal interface materials improves with increasing contact pressure. The use of ther-
mal grease significantly reduces the interface thermal resistance. That is, the bare joint results in a thermal
resistance approximately 7 times greater than the thermal grease joint.
Figure 19. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
External Resistance
External Resistance
Internal Resistance
(Note the internal versus external package resistance.)
Radiation
Convection
Radiation
Convection
Heat Sink
Die/Package
Chip Junction
Printed-Circuit Board
Thermal Interface Material
Package/Leads
相關PDF資料 |
PDF描述 |
|---|---|
| PP-MOD1V2 | ISP INTERFACE MODULE |
| PP01002 | GEHOERSCHUTZ OHRSTOEPSEL 250ST Inhalt pro Packung: 250 Stk. |
| PP0901SA | Direct ProTek Replacement:PP0901SA |
| PP0901SB | Direct ProTek Replacement:PP0901SB |
| PP1101SB | Direct ProTek Replacement:PP1101SB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| POWERPLUG15W | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:AC/DC POWER SUPPLY |
| POWERPLUG24W | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:AC/DC POWER SUPPLY |
| POWERPLUS 2C 2500MAH | 制造商:Energizer Battery Company 功能描述: |
| POWERPLUS 2D 2500MAH | 制造商:Energizer Battery Company 功能描述: |
| POWERPLUS 4AAA 850MAH | 制造商:Energizer Battery Company 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。