Page 6
Version 2.0
Datasheet
9/30/99
PowerPC 750 SCM RISC Microprocessor
PID8p-750
Preliminary Copy
Electrical and Thermal Characteristics
This section provides both AC and DC electrical specifications and thermal characteristics for the PID8p-750.
DC Electrical Characteristics
The tables in this section describe the PID8p-750’s DC electrical characteristics. The following table provides
the absolute maximum ratings.
The following table provides the recommended operating conditions for the PID8p-750.
Absolute Maximum Ratings
Characteristic
Symbol
Value
Unit
Core supply voltage
V
DD
-0.3 to 2.5
V
PLL supply voltage
AV
DD
-0.3 to 2.5
V
L2 DLL supply voltage
L2AV
DD
-0.3 to 2.5
V
60x bus supply voltage (maximum)
OV
DD(3.3V)
-0.3 to 3.6
V
OV
DD(2.5V)
-0.3 to 2.8
OV
DD(1.8V)
-0.3 to 2.1
L2 bus supply voltage (maximum)
L2OV
DD
-0.3 to 3.6
V
Input voltage (maximum)
V
IN(3.3V)
-0.3 to 3.6
V
V
IN(2.5V)
-0.3 to 2.8
V
IN(1.8V)
-0.3 to 2.1
Storage temperature range
T
STG
-55 to 150
°
C
Note:
1. Functional and tested operating conditions are given in Table ”Recommended Operating Conditions1,2,3,” below. Absolute maximum ratings are
stress ratings only, and functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause per-
manent damage to the device.
2.
Caution:
V
IN
must not exceed OV
DD
by more than 0.3V at any time, including during power-on reset.
3.
Caution:
OV
DD
/ L2OV
must not exceed V
/AV
by more than 2.0V during normal operation. On power up and power down, OV
DD
/ L2OV
DD
must not
exceed V
DD
/AV
DD
by more than 3.3V and for no more than 20ms.
4.
Caution:
V
DD
/AV
must not exceed OV
/ L2OV
by more than 0.4V during normal operation. On power up and power down, V
DD
/AV
DD
must not
exceed OV
DD
/ L2OV
DD
by more than 1.0V and for no more than 20ms.
Recommended Operating Conditions
1,2,3
Characteristic
Symbol
Value
Unit
Core supply voltage
V
DD
2.0 to 2.1
V
PLL supply voltage
AV
DD
2.0 to 2.1
V
L2 DLL supply voltage
L2AV
DD
2.0 to 2.1
V
60x bus supply voltage, pin W1 tied high
OV
DD(3.3V)
3.135 to 3.465
V
60x bus supply voltage, pin W1 tied to HRESET
OV
DD(2.5V)
2.375 to 2.625
V
60x bus supply voltage, pin W1 tied to GND
OV
DD(1.8V)
1.71 to 1.89
V
L2 bus supply voltage, pin A19 tied high
L2OV
DD(3.3V)
3.135 to 3.465
V
Note:
1. These are recommended and tested operating conditions. Proper device operation outside of these conditions is not guaranteed.
2. For dd3.x, If W1 is left unconnected, the 60X bus will default to OV
DD
= 3.3V. For dd2x, W1=Don’t care
3. For dd3.x, If A19 is left unconnected, the L2 bus will default to L2OV
DD
= 3.3V. For dd2x, W1=Don’t care