參數資料
型號： PowerPC 750
廠商： IBM Microeletronics
英文描述： 32-Bit Embedded Microprocessor(32位精簡指令集嵌入式微處理器)
中文描述： 32位嵌入式微處理器（32位精簡指令集嵌入式微處理器）
文件頁數： 37/46頁
文件大?。?/td> 610K
代理商： POWERPC 750
9/30/99
Version 2.0
Datasheet
Page 33
PowerPC 750 SCM RISC Microprocessor
Preliminary Copy
PID8p-750
Pull-up / Pull-down Resistor Requirements
The PID8p-750 requires high-resistive (weak: 10K
) pull-up resistors on several control signals of the bus
interface to maintain the control signals in the negated state after they have been actively negated and
released by the PID8p-750 or other bus masters. These signals are: TS, ABB, DBB, and ARTRY.
In addition, the PID8p-750 has one open-drain style output that requires a pull-up resistor (weak or stronger:
4.7K
- 1- K
) if it is used by the system. This signal is: CKSTP_OUT.
If address or data parity is not used by the system, and the respective parity checking is disabled through
HID0, the input receivers for those pins are disabled. If all parity generation is disabled through HID0, than all
parity checking should also be disabled through HID0. It is still recommended that the unused address or
data parity signals be tied high through pull up resistors to minimize noise on the package.
No pull-up resistors are normally required for the L2 interface.
HRESET Requirements
HRESET needs to be actively driven.
Resistor Pull-up / Pull-down Requirements
Required or Recommended Actions
Signals
Strong pull-up required
CKSTP_OUT
Weak pull-up required
TLBISYNC, LSSD_MODE, L1_TSTCLK, L2_TSTCLK, TS, ABB, DBB,
ARTRY,
Weak pull-up or pull-down required
TCK
Weak pull-up recommended
SRESET, GBL, TBST,SMI, INT, MCP, CKSTP_IN
Weak pull-up recommended if pin not used
AP0-AP3, DP0-DP7
Note:
See “PowerPC PID8p-750 Microprocessor Pinout Listings” section on page 24 for additional comments about these signals.
相關PDF資料
PDF描述
PP-MOD1V2 ISP INTERFACE MODULE
PP01002 GEHOERSCHUTZ OHRSTOEPSEL 250ST Inhalt pro Packung: 250 Stk.
PP0901SA Direct ProTek Replacement:PP0901SA
PP0901SB Direct ProTek Replacement:PP0901SB
PP1101SB Direct ProTek Replacement:PP1101SB
相關代理商/技術參數
參數描述
POWERPLUG15W 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:AC/DC POWER SUPPLY
POWERPLUG24W 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:AC/DC POWER SUPPLY
POWERPLUS 2C 2500MAH 制造商:Energizer Battery Company 功能描述:
POWERPLUS 2D 2500MAH 制造商:Energizer Battery Company 功能描述:
POWERPLUS 4AAA 850MAH 制造商:Energizer Battery Company 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*