參數資料
型號： PI7C7300A
廠商： Pericom Semiconductor Corp.
英文描述： 3-PORT PCI-to-PCI BRIDGE
中文描述： 3端口PCI至PCI橋
文件頁數： 41/109頁
文件大小： 779K
代理商： PI7C7300A
PI7C7300A
3-PORT PCI-TO-PCI BRIDGE
ADVANCE INFORMATION
Page 41 OF 109
09/25/03 Revision 1.09
!
!
!
Two 32-bit I/O address ranges
Two 32-bit memory-mapped I/O (non-prefetchable memory) ranges
Two 32-bit prefetchable memory address ranges
Transactions falling within these ranges are forwarded downstream from the primary PCI
bus to the two secondary PCI buses. Transactions falling outside these ranges are
forwarded upstream from the two secondary PCI buses to the primary PCI bus.
No address translation is required in PI7C7300A. The addresses that are not marked for
downstream are always forwarded upstream. However, if an address of a transaction
initiated from S1 bus is located in the marked address range for down-stream in S2 bus
and not in the marked address range for downstream in S1 bus, the transaction will be
forwarded to S2 bus instead of primary bus. By the same token, if an address of a
transaction initiated from S2 bus is located in the marked address range for downstream
in S1 bus and not in the marked address range for downstream in S2 bus, the transaction
will be forwarded to S1 bus instead of primary bus.
5.2
I/O ADDRESS DECODING
PI7C7300A uses the following mechanisms that are defined in the configuration space to
specify the I/O address space for downstream and upstream forwarding:
!
I/O base and limit address registers
!
The ISA enable bit
!
The VGA mode bit
!
The VGA snoop bit
This section provides information on the I/O address registers and ISA mode. Section
5.4 provides information on the VGA modes.
To enable downstream forwarding of I/O transactions, the I/O enable bit must be set in
the command register in configuration space. All I/O transactions initiated on the primary
bus will be ignored if the I/O enable bit is not set. To enable upstream forwarding of I/O
transactions, the master enable bit must be set in the command register. If the master-
enable bit is not set, PI7C7300A ignores all I/O and memory transactions initiated on the
secondary bus.
The master-enable bit also allows upstream forwarding of memory transactions
if it is set.
CAUTION
If any configuration state affecting I/O transaction forwarding is changed by a
configuration write operation on the primary bus at the same time that I/O
transactions are ongoing on the secondary bus, PI7C7300A response to the secondary
bus I/O transactions is not predictable. Configure the I/O base and limit address
registers, ISA enable bit, VGA mode bit, and VGA snoop bit before setting I/O enable
相關PDF資料
PDF描述
PI7C7300ANA 3-PORT PCI-to-PCI BRIDGE
PI7C8140A 2 PORT PCI TO PCI BRIDGE PLX PCI 6140 COMPARISON
PI7C8148B 2-PORT PCI-to-PCI BRIDGE PLX PC16152 COMPARISON
PI7C8150B-33 PCI Bridge | Asynchronous 2-Port PCI Bridge
PI7C8152B PCI Bridge | Asynchronous 2-Port PCI Bridge
相關代理商/技術參數
參數描述
PI7C7300AEVB-3 功能描述:界面開發工具 3 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
PI7C7300ANA 制造商:Pericom Semiconductor Corporation 功能描述:PCI-to-PCI Bridge 272-Pin BGA 制造商:Pericom Semiconductor Corporation 功能描述:PCI to PCI Bridge 272-Pin BGA
PI7C7300ANAE 功能描述:外圍驅動器與原件 - PCI 3 Port PCI Bridge RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C7300ANA-E 制造商:Pericom Semiconductor Corporation 功能描述:PCI-to-PCI Bridge 272-Pin BGA 制造商:Pericom Semiconductor Corporation 功能描述:PCI to PCI Bridge 272-Pin BGA
PI7C7300DNAE 功能描述:外圍驅動器與原件 - PCI PCI -to -PCI Bridge 3 Port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*