- 您現在的位置：買賣IC網 > PDF目錄367854 > PDI1394L21 (NXP Semiconductors N.V.) Full Duplex AV Link Layer Ccontroller(全雙工AV鏈接層控制器) PDF資料下載
參數資料
| 型號： | PDI1394L21 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full Duplex AV Link Layer Ccontroller(全雙工AV鏈接層控制器) |
| 中文描述： | 全雙工鏈路層Ccontroller影音（全雙工視聽鏈接層控制器） |
| 文件頁數： | 32/54頁 |
| 文件大?。?/td> | 242K |
| 代理商： | PDI1394L21 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
Philips Semiconductors
Preliminary specification
PDI1394L21
1394 full duplex AV link layer controller
2000 Jun 06
32
13.1.7
This register is the top level interrupt status register. If the external interrupt line is set, this register will indicate which major portion of the AV
Link generated the interrupt. There is no interrupt acknowledge required at this level. These bits auto clear when the interrupts in the
appropriate section of the device are cleared or disabled. Control of the AV transceiver is also provided by this register.
Global Interrupt Status and TX Control (GLOBCSR) – Base Address: 0x018
Bits 0 to 3 are used to identify which internal modules are currently generating an interrupt. After identifying the module, the appropriate register
in that module must be read to determine the exact cause of the interrupt.
NOTES
1. There can be more than one interrupt source active at the same time.
2. The HIF INT_N signal (pin 28) remains active as long as there is at least one more enabled active interrupt status bit.
29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
A
I
I
L
31 30
E
E
E
E
D
E
E
SV00857
Reset Value 0x00010000
Bit 18:
R/W
Enable output AVPORT2: A ‘1’ enables AVPORT2 as an output. A ‘0’ sets the 3-State condition on the port. In
3-State condition the port may be used as an input or unused output according to the state of DIRAV1 (bit 16).
Enable output AVPORT1: A ‘1’ enables AVPORT1 as an output. A ‘0’ sets the 3-State condition on the port. In
3-State condition the port may be used as an input or unused output according to the state of DIRAV1 (bit 16).
Direction of AVPORT1 (DIRAV1): A ‘1’ enables AVPORT1 as a transmitter, thus AVPORT1 pins are inputs. A ‘0’
configures AVPORT1 as a receiver, AVPORT1 pins are outputs in this configuration. The configuration of AVPORT2
pins is opposite of AVPORT1 pins. When AVPORT1 is set to transmit, AVPORT2 receives and vice versa.
Enables generation of external interrupt by asynchronous transmitter and receiver module (ASYTX/RX, bit 3) when
set (1). Disables such interrupts when clear (0) (regardless of ASYINTE contents).
Enables generation of external interrupt by the isochronous transmitter module (ITXINT, bit 2) when set (1).
Disables such interrupts when clear (0) (regardless of ITXINTE contents).
Enables generation of external interrupt by the isochronous receiver module (IRXINT, bit 1) when set (1).
Disables such interrupts when clear (0) (regardless of IRXINTE contents).
Enables generation of external interrupt by general link/phy module (LKPHYINT, bit 0) when set (1). Disables such
interrupts when clear (0) (regardless of LNKPHYINTE contents).
Asynchronous Transmitter/Receiver Interrupt (ASYITX/RX): Interrupt source is in the Asynchronous Transmitter/
Receiver Interrupt Acknowledge/Source register.
AV Transmitter Interrupt (ITXINT): Interrupt source is in the AV Transmitter Interrupt Acknowledge/Source register.
AV Receiver Interrupt (IRXINT): Interrupt source is in the AV Receiver Interrupt Acknowledge/Source register.
Link-Phy Interrupt (LNKPHYINT): Interrupt source is in the Link Phy Interrupt Acknowledge register.
Bit 17:
R/W
Bit 16:
R/W
Bit 11:
R/W
Bit 10:
R/W
Bit 9:
R/W
Bit 8:
R/W
Bit 3:
R
Bit 2:
Bit 1:
Bit 0:
R
R
R
相關PDF資料 |
PDF描述 |
|---|---|
| PDI1394L41 | Content Protection AV Link Layer(內容可保護的AV鏈接層控制器) |
| PDI1394P21 | 3-port Physical Layer Interface(三端口物理層接口) |
| PDI1394P22 | 3-port Physical Layer Interface(三端口物理層接口) |
| PDI1394P24 | 2-port 400 Mbps physical layer interface(2端口 400 Mbps物理層接口) |
| PDI40C1D00 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDI1394L21BE | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1394 full duplex AV link layer controller |
| PDI1394L21BP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1394 full duplex AV link layer controller |
| PDI1394L40 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1394 enhanced AV link layer controller |
| PDI1394L40BE | 制造商:NXP Semiconductors 功能描述:1 CHANNEL(S), 400M BPS, SERIAL COMM CONTROLLER, PQFP144 |
| PDI1394L40BE,518 | 功能描述:視頻 IC 1394 A/V LINK LAYER RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。