- 您現在的位置：買賣IC網 > PDF目錄367854 > PDI1394L21 (NXP Semiconductors N.V.) Full Duplex AV Link Layer Ccontroller(全雙工AV鏈接層控制器) PDF資料下載
參數資料
| 型號： | PDI1394L21 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Full Duplex AV Link Layer Ccontroller(全雙工AV鏈接層控制器) |
| 中文描述： | 全雙工鏈路層Ccontroller影音（全雙工視聽鏈接層控制器） |
| 文件頁數： | 18/54頁 |
| 文件大小： | 242K |
| 代理商： | PDI1394L21 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
Philips Semiconductors
Preliminary specification
PDI1394L21
1394 full duplex AV link layer controller
2000 Jun 06
18
Table 5.
Asynchronous Receive Fields
Field Name
Description
destinationID
This field is the concatenation of busNumbers (or all ones for “l(fā)ocal bus”) and nodeNumbers (or all ones for
broadcast) for this node.
tLabel
This field is the transaction label, which is used to pair up a response packet with its corresponding request packet.
rt
The retry code for this packet. 00=retry1, 01=retryX, 10=retryA, 11=retryB.
tCode
The transaction code for this packet.
priority
The priority level for this packet (0000 for cable environment).
sourceID
This is the node ID of the sender of this packet.
destinationOffsetHigh,
destinationOffsetLow
The concatenation of these two field addresses a quadlet in this node’s address space.
rCode
Response code for response packets.
quadlet data
For quadlet write requests and quadlet read responses, this field holds the data received.
dataLength
The number of bytes of data to be received in a block packet.
extendedTcode
If the tCode indicates a lock transaction, this specifies the actual lock action to be performed with the data in this
packet.
block data
The data received. If dataLength=0, no data will be written into the FIFO for this field. Regardless of the destination
or source alignment of the data, the first byte of the block will appear in the high order byte of the first quadlet.
padding
If the dataLength mod 4 is not zero, then zero-value bytes are added onto the end of the packet to guarantee that a
whole number of quadlets is sent.
u
Unsolicited response tag bit. This bit is set to one (1) if the received response was unsolicited.
ackSent
This field contains the acknowledge code that the link layer returned to the sender of the received packet. For
packets that do not need to be acknowledged (such as broadcasts) the field contains the acknowledge value that
would have been sent if an acknowledge had been required. The values for this field are listed in Table 6 (they also
can be found in the IEEE 1394 standard).
Table 6.
Acknowledge codes
Code
Name
Description
0001
ack_complete
The node has successfully accepted the packet. If the packet was a request subaction, the
destination node has successfully completed the transaction and no response subaction shall follow.
0010
ack_pending
The node has successfully accepted the packet. If the packet was a request subaction, a response
subaction will follow at a later time. This code shall not be returned for a response subaction.
0100
ack_busy_X
The packet could not be accepted. The destination transaction layer may accept the packet on a
retry of the subaction.
0101
ack_busy_A
The packet could not be accepted. The destination transaction layer will accept the packet when the
node is not busy during the next occurrence of retry phase A.
0110
ack_busy_B
The packet could not be accepted. The destination transaction layer will accept the packet when the
node is not busy during the next occurrence of retry phase B.
1101
ack_data_error
The node could not accept the block packet because the data field failed the CRC check, or because
the length of the data block payload did not match the length contained in the dataLength field. This
code shall not be returned for any packet that does not have a data block payload.
1110
ack_type_error
A field in the request packet header was set to an unsupported or incorrect value, or an invalid
transaction was attempted (e.g., a write to a read-only address).
0000, 0011,
0111 – 1100,
and 1111
reserved
This revision of the AV Link will not generate other acknowledge codes, but may receive them from
newer (1394 A) links. In that case, these new values will show up here.
NOTE:
1. Upon receipt of a broadcast packet, if any ACK code other than ACK_DATA_ERROR is produced, asume packet receipt was OK.
ACK_DATA ERROR indicates the packet was received with an error, appropriate steps should be taken to ignore the packet and inform the
sending node of the error.
相關PDF資料 |
PDF描述 |
|---|---|
| PDI1394L41 | Content Protection AV Link Layer(內容可保護的AV鏈接層控制器) |
| PDI1394P21 | 3-port Physical Layer Interface(三端口物理層接口) |
| PDI1394P22 | 3-port Physical Layer Interface(三端口物理層接口) |
| PDI1394P24 | 2-port 400 Mbps physical layer interface(2端口 400 Mbps物理層接口) |
| PDI40C1D00 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDI1394L21BE | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1394 full duplex AV link layer controller |
| PDI1394L21BP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1394 full duplex AV link layer controller |
| PDI1394L40 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1394 enhanced AV link layer controller |
| PDI1394L40BE | 制造商:NXP Semiconductors 功能描述:1 CHANNEL(S), 400M BPS, SERIAL COMM CONTROLLER, PQFP144 |
| PDI1394L40BE,518 | 功能描述:視頻 IC 1394 A/V LINK LAYER RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。