- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9665N (NXP SEMICONDUCTORS) Fm+ parallel bus to I2C-bus controller PDF資料下載
參數資料
| 型號： | PCA9665N |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Fm+ parallel bus to I2C-bus controller |
| 中文描述： | I2C BUS CONTROLLER, PDIP20 |
| 封裝： | 0.300 INCH, PLASTIC, MS-001, SOT146-1, DIP-20 |
| 文件頁數： | 85/91頁 |
| 文件大?。?/td> | 372K |
| 代理商： | PCA9665N |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁
PCA9665_2
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 7 December 2006
85 of 91
NXP Semiconductors
PCA9665
Fm+ parallel bus to I
2
C-bus controller
17.3.2
Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250
°
C
or 265
°
C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
17.3.3
Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300
°
C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 seconds to 5 seconds between 270
°
C and 320
°
C.
17.4 Package related soldering information
Table 56.
Mounting
Suitability of IC packages for wave, reflow and dipping soldering methods
Package
[1]
Soldering method
Wave
suitable
suitable
[3]
not suitable
Reflow
[2]
not suitable
Dipping
suitable
Through-hole mount
CPGA, HCPGA
DBS, DIP, HDIP, RDBS, SDIP, SIL
PMFP
[4]
Through-hole-surface
mount
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9671 | Remote 16-bit I/O expander for Fm+ I2C-bus with reset |
| PCA9671DB | Remote 16-bit I/O expander for Fm+ I2C-bus with reset |
| PCA9671DK | Remote 16-bit I/O expander for Fm+ I2C-bus with reset |
| PCA9673 | Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset |
| PCA9673DB | Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9665N,112 | 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| PCA9665PW | 制造商:NXP Semiconductors 功能描述:IC CNTRLR PARALLEL I2C 20TS 制造商:UNBRANDED 功能描述:UNIVERSAL BUS FUNCTIONS FM+12C BUS *NIC* 制造商:NXP Semiconductors 功能描述:IC, CNTRLR PARALLEL, I2C, 20TSSOP 制造商:NXP Semiconductors 功能描述:IC, CNTRLR PARALLEL, I2C, 20TSSOP; Interface Type:I2C, Parallel, SMBus; Interface Applications:I2C Bus & SMBus Systems Applications; Supply Voltage Min:2.3V; Supply Voltage Max:3.6V; Digital IC Case Style:TSSOP; No. of Pins:20; ;RoHS Compliant: Yes |
| PCA9665PW,112 | 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| PCA9665PW,118 | 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| PCA9665PW,118-CUT TAPE | 制造商:NXP 功能描述:PCA9635 Series 1 MHz Fm + Parallel Bus to I2C-Bus Controller - TSSOP-20 |
發布緊急采購，3分鐘左右您將得到回復。