參數資料
型號： PCA9665N
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： Fm+ parallel bus to I2C-bus controller
中文描述： I2C BUS CONTROLLER, PDIP20
封裝： 0.300 INCH, PLASTIC, MS-001, SOT146-1, DIP-20
文件頁數： 16/91頁
文件大?。?/td> 372K
代理商： PCA9665N
PCA9665_2
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 7 December 2006
16 of 91
NXP Semiconductors
PCA9665
Fm+ parallel bus to I
2
C-bus controller
8.
PCA9665 modes
8.1 Configuration modes
Byte mode and Buffered mode are selected using the MODE bit in I2CCON register:
MODE = 0: Byte mode
MODE = 1: Buffered mode
8.1.1
Byte mode
The Byte mode allows communication on a single command basis. Only one specific
command is executed at a time and the Status Register is updated once this single
command has been performed. A command can be a START, a STOP, a Byte Write, a
Byte Read, and so on.
8.1.2
Buffered mode
The Buffered mode allows several instructions to be executed before an Interrupt is
generated and before the I2CSTA register is updated. This allows the microcontroller to
request a sequence, up to 68 bytes in a single transmission and lets the PCA9665
perform it without having to access the Status Register and the Control Register each time
a single command is performed. The microcontroller can then perform other tasks while
the PCA9665 performs the requested sequence.
The number of bytes that needs to be sent from the internal buffer (Transmitter mode) or
received into the internal buffer (Receiver mode) is defined in the indirectly addressed
I2CCOUNT Register (BC[6:0]). Up to 68 bytes can be sent or received.
8.2 Operating modes
The four operating modes are:
Master Transmitter
Master Receiver
Slave Receiver
Slave Transmitter
Each mode can be used on a byte basis (Byte mode) or in an up to 68-byte buffer basis
(Buffered mode).
Data transfers in each mode of operation are shown in
Figure 7
through
Figure 10
. These
figures contain the following abbreviations:
S —
START condition
SLA —
7-bit slave address
R —
Read bit (HIGH level at SDA)
W —
Write bit (LOW level at SDA)
A —
Acknowledge bit (LOW level at SDA)
A —
Not acknowledge bit (HIGH level at SDA)
Data —
8-bit data byte
相關PDF資料
PDF描述
PCA9671 Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DB Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DK Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9673 Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset
PCA9673DB Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset
相關代理商/技術參數
參數描述
PCA9665N,112 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665PW 制造商:NXP Semiconductors 功能描述:IC CNTRLR PARALLEL I2C 20TS 制造商:UNBRANDED 功能描述:UNIVERSAL BUS FUNCTIONS FM+12C BUS *NIC* 制造商:NXP Semiconductors 功能描述:IC, CNTRLR PARALLEL, I2C, 20TSSOP 制造商:NXP Semiconductors 功能描述:IC, CNTRLR PARALLEL, I2C, 20TSSOP; Interface Type:I2C, Parallel, SMBus; Interface Applications:I2C Bus & SMBus Systems Applications; Supply Voltage Min:2.3V; Supply Voltage Max:3.6V; Digital IC Case Style:TSSOP; No. of Pins:20; ;RoHS Compliant: Yes
PCA9665PW,112 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665PW,118 功能描述:I2C 接口集成電路 FM+ I2C BUS CONTRLLR RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16
PCA9665PW,118-CUT TAPE 制造商:NXP 功能描述:PCA9635 Series 1 MHz Fm + Parallel Bus to I2C-Bus Controller - TSSOP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*