- 您現在的位置：買賣IC網 > PDF目錄363718 > NZ48F4L0QTZ (Intel Corp.) StrataFlash Wireless Memory PDF資料下載
參數資料
| 型號： | NZ48F4L0QTZ |
| 廠商： | Intel Corp. |
| 英文描述： | StrataFlash Wireless Memory |
| 中文描述： | 無線的StrataFlash存儲器 |
| 文件頁數： | 51/106頁 |
| 文件大?。?/td> | 1272K |
| 代理商： | NZ48F4L0QTZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
Intel StrataFlash Wireless Memory (L18)
Datasheet
Intel StrataFlash Wireless Memory (L18)
Order Number: 251902, Revision: 009
April 2005
51
During synchronous array and non-array read modes, the first word is output from the data buffer
on the next valid CLK edge after the initial access latency delay (see
Section 10.3.2, “Latency
Count” on page 52
). Subsequent data is output on valid CLK edges following a minimum delay.
However, for a synchronous non-array read, the same word of data will be output on successive
clock edges until the burst length requirements are satisfied.
Figure 14Figure 16
10.2.1
Burst Suspend
The Burst Suspend feature of the device can reduce or eliminate the initial access latency incurred
when system software needs to suspend a burst sequence that is in progress in order to retrieve data
from another device on the same system bus. The system processor can resume the burst sequence
later. Burst suspend provides maximum benefit in non-cache systems.
Burst accesses can be suspended during the initial access latency (before data is received) or after
the device has output data. When a burst access is suspended, internal array sensing continues and
any previously latched internal data is retained. A burst sequence can be suspended and resumed
without limit as long as device operation conditions are met.
Burst Suspend occurs when CE# is asserted, the current address has been latched (either ADV#
rising edge or valid CLK edge), CLK is halted, and OE# is deasserted. CLK can be halted when it
is at V
IH
or V
IL
. WAIT is in High-Z during OE# deassertion.
To resume the burst access, OE# is reasserted, and CLK is restarted. Subsequent CLK edges
resume the burst sequence.
Within the device, CE# and OE# gate WAIT. Therefore, during Burst Suspend WAIT is placed in
high-impedance state when OE# is deasserted and resumed active when OE# is re-asserted. See
Figure 17, “Burst Suspend Timing” on page 36
.
10.3
Read Configuration Register (RCR)
The RCR is used to select the read mode (synchronous or asynchronous), and it defines the
synchronous burst characteristics of the device. To modify RCR settings, use the Configure Read
Configuration Register command (see
Section 9.2, “Device Commands” on page 47
).
RCR contents can be examined using the Read Device Identifier command, and then reading from
<partition base address> + 0x05 (see
Section 15.2, “Read Device Identifier” on page 76
).
The RCR is shown in
Table 10
. The following sections describe each RCR bit.
Table 10.
Read Configuration Register Description (Sheet 1 of 2)
Read Configuration Register (RCR)
Read
Mode
RES
Latency Count
WAIT
Polarity
Data
Hold
WAIT
Delay
Burst
Seq
CLK
Edge
RES
RES
Burst
Wrap
Burst Length
RM
R
LC[2:0]
WP
DH
WD
BS
CE
R
R
BW
BL[2:0]
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Bit
Name
Description
相關PDF資料 |
PDF描述 |
|---|---|
| NZD560A | NPN Low Saturation Transistor |
| NZF220DFT1G | EMI Filter with ESD Protection |
| NZF220TT1 | EMI Filter with ESD Protection(帶ESD保護功能的EMI濾波器) |
| NZL5V1AXV3T1 | Zener Voltage Regulators (SC-89 Dual Common Anode Zeners for ESD Protection) |
| NZL5V6AXV3T1 | Zener Voltage Regulators(齊納穩壓管) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NZ600N18K | 制造商:n/a 功能描述:Power Module |
| NZ9F10VST5G | 功能描述:穩壓二極管 ZENER DIODE RoHS:否 制造商:Vishay Semiconductors 齊納電壓:12 V 電壓容差:5 % 電壓溫度系數:0.075 % / K 齊納電流: 功率耗散:3 W 最大反向漏泄電流:3 uA 最大齊納阻抗:7 Ohms 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AC 封裝:Reel |
| NZ9F10VT5G | 功能描述:穩壓二極管 ZENER DIODE RoHS:否 制造商:Vishay Semiconductors 齊納電壓:12 V 電壓容差:5 % 電壓溫度系數:0.075 % / K 齊納電流: 功率耗散:3 W 最大反向漏泄電流:3 uA 最大齊納阻抗:7 Ohms 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AC 封裝:Reel |
| NZ9F11VST5G | 功能描述:穩壓二極管 ZENER DIODE RoHS:否 制造商:Vishay Semiconductors 齊納電壓:12 V 電壓容差:5 % 電壓溫度系數:0.075 % / K 齊納電流: 功率耗散:3 W 最大反向漏泄電流:3 uA 最大齊納阻抗:7 Ohms 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AC 封裝:Reel |
| NZ9F11VT5G | 功能描述:穩壓二極管 ZENER DIODE RoHS:否 制造商:Vishay Semiconductors 齊納電壓:12 V 電壓容差:5 % 電壓溫度系數:0.075 % / K 齊納電流: 功率耗散:3 W 最大反向漏泄電流:3 uA 最大齊納阻抗:7 Ohms 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:DO-214AC 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。