參數資料
型號: MCIMX514AJM6C
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: SPECIALTY MICROPROCESSOR CIRCUIT, PBGA529
封裝: 19 X 19 MM, 0.8 MM PITCH, ROHS COMPLIANT, BGA-529
文件頁數: 145/172頁
文件大小: 2218K
代理商: MCIMX514AJM6C
i.MX51A Automotive and Infotainment Applications Processors, Rev. 4
74
Freescale Semiconductor
Electrical Characteristics
4.7.4
FEC AC Timing Parameters
This section describes the electrical information of the Fast Ethernet Controller (FEC) module. The FEC
is designed to support both 10 and 100 Mbps Ethernet/IEEE 802.3 networks. An external transceiver
interface and transceiver function are required to complete the interface to the media. The FEC supports
the 10/100 Mbps MII (18 pins in total) and the 10 Mbps-only 7-wire interface, which uses 7 of the MII
pins, for connection to an external Ethernet transceiver. For the pin list of MII and 7-wire, refer to the
i.MX51 Multimedia Applications Processor Reference Manual (MCIMX51RM).
This section describes the AC timing specifications of the FEC.
4.7.4.1
MII Receive Signal Timing
The MII receive signal timing involves the FEC_RXD[3:0], FEC_RX_DV, FEC_RX_ER, and
FEC_RX_CLK signals. The receiver functions correctly up to a FEC_RX_CLK maximum frequency of
25 MHz + 1%. There is no minimum frequency requirement but the processor clock frequency must
exceed twice the FEC_RX_CLK frequency. Table 70 lists the MII receive channel signal timing
parameters and Figure 42 shows MII receive signal timings.
.
SD7
eSDHC Input Setup Time
tISU
2.5
ns
SD8
eSDHC Input Hold Time
tIH
5
2.5
ns
1 In low speed mode, card clock must be lower than 400 kHz, voltage ranges from 2.7 to 3.6 V.
2 In normal speed mode for SD/SDIO card, clock frequency can be any value between 025 MHz. In high-speed mode, clock
frequency can be any value between 0
50 MHz.
3 In normal speed mode for MMC card, clock frequency can be any value between 020 MHz. In high-speed mode, clock
frequency can be any value between 0
52 MHz.
4 Measurement taken with CLoad = 20 pF
5 To satisfy hold timing, the delay difference between clock input and cmd/data input must not exceed 2 ns.
Table 70. MII Receive Signal Timing
Num
Characteristic1
1 FEC_RX_DV, FEC_RX_CLK, and FEC_RXD0 have same timing in 10 Mbps 7-wire interface mode.
Min
Max
Unit
M1
FEC_RXD[3:0], FEC_RX_DV, FEC_RX_ER to FEC_RX_CLK setup
5
ns
M2
FEC_RX_CLK to FEC_RXD[3:0], FEC_RX_DV, FEC_RX_ER hold
5
ns
M3
FEC_RX_CLK pulse width high
35%
65%
FEC_RX_CLK period
M4
FEC_RX_CLK pulse width low
35%
65%
FEC_RX_CLK period
Table 69. eSDHCv2 Interface Timing Specification (continued)
ID
Parameter
Symbols
Min
Max
Unit
相關PDF資料
PDF描述
MCIMX537CVV8C 32-BIT, 800 MHz, RISC PROCESSOR, PBGA529
MCM16Y1BACFT16 16-BIT, MROM, MICROCONTROLLER, PQFP160
MCM16Y1BGCFT16 16-BIT, MROM, MICROCONTROLLER, PQFP160
M68HC16Y1CFC 16-BIT, MROM, MICROCONTROLLER, PQFP16
MCV14AI/SL 8-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PDSO14
相關代理商/技術參數
參數描述
MCIMX514AJM6CR2 制造商:Freescale Semiconductor 功能描述:ELVIS 3.0 AUTO - Tape and Reel
MCIMX515CJM6C 功能描述:處理器 - 專門應用 iMX515 App Processor RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX515CJM6CR2 功能描述:處理器 - 專門應用 i.MX51 32bit 800 MHz RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX515DJM8C 功能描述:處理器 - 專門應用 iMX515 App Processor Extended Temp RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
MCIMX515DJM8C 制造商:Freescale Semiconductor 功能描述:; LEADED PROCESS COMPATIBLE:YES; PEAK RE