參數資料
型號： M37640E8FP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
封裝： 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80
文件頁數： 30/96頁
文件大?。?/td> 1477K
代理商： M37640E8FP
36
Ver 1.4
MITSUBISHI MICROCOMPUTERS
7640 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
1.17.4 Timer 2
Timer 2 is an 8-bit timer with an 8-bit reload latch (see
Figure 1.35).
T123M7 (bit 7 of T123M) is the Timer 1 and 2 Data
Write Control Bit. If T123M7 is “1”, data written to
Timer 2 is placed only in the Timer 2 reload latch (see
Figure 1.32). The latch value is loaded into Timer 2
after Timer 2 underflows. If the T123M7 is “0”, the
value written to Timer 2 is placed in Timer 2 and the
Timer 2 reload latch. At reset, T123M2 is set to a “0”.
The Timer 2 reload latch value is not affected by a
change of the count source. However, because
changing the count source may cause an inadvertent
countdown of the timer, the timer should be rewritten
when the count source is changed.
Timer Mode
Count Source:
If T123M3 is “0”, the Timer 2 count source is the
Timer 1 underflow output.
If T123M3 is “1”, the Timer 2 count source is
F.
In Timer mode, each time the timer underflows, the
corresponding timer interrupt request bit is set to a
“1”, the contents of the timer latch are loaded into
the timer, and the count down sequence begins
again.
Pulse Output Mode
Count Source:
If T123M3 is “0”, the Timer 2 count source is the
Timer 1 underflow output.
If T123M3 is “1”, the Timer 2 count source is
F.
Timer 2 Pulse Output mode is enabled by setting
T123M6 to a “1” and T123M0 to a “1”. Each time the
Timer 2 underflows, the output of the TOUT pin is
inverted, and the corresponding Timer 2 interrupt
request bit is set to a “1”. The repeated inversion of
the TOUT pin output produces a rectangular wave-
form with a duty ratio of 50 percent. The initial level
of the output is determined by the TOUT polarity se-
lect bit (T123M5). When this bit is “0”, the output
starts from a high level. When this bit is “1”, the out-
put starts from a low level.
1.17.5 Timer 3
Timer 3 is an 8-bit timer with an 8-bit reload latch (see
Figure 1.35). The Timer 3 reload latch value is not af-
fected by a change of the count source. Because
changing the count source may cause an inadvertent
countdown of the timer, the timer should be rewritten
whenever the count source is changed.
Timer Mode
Count Source:
If T123M4 is “0”, the Timer 3 count source is the
Timer 1 underflow output.
If T123M4 is “1”, the count source is
F/8
In Timer mode, each time the timer underflows, the
corresponding timer interrupt request bit is set to a
“1”, the contents of the timer latch are loaded into the
timer, and the count down sequence begins again.
Data written to Timer 3 is always placed in Timer 3
and the Timer 3 reload latch.
相關PDF資料
PDF描述
M37643M8-XXXHP 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M37643F8HP 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80
M37700E2AFS 16-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQCC80
M37700E2AXXXFP 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP80
M37701E2-XXXSP 16-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP64
相關代理商/技術參數
參數描述
M37640E8FS 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
M37640M4T 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-111FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-126FP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37640M8-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE CHIP 8 BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*