- 您現在的位置：買賣IC網 > PDF目錄69014 > M37640E8FP 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | M37640E8FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 28/96頁 |
| 文件大?。?/td> | 1477K |
| 代理商： | M37640E8FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
34
Ver 1.4
MITSUBISHI MICROCOMPUTERS
7640 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Each time the Timer Y underflows, the output of the
CNTR1 pin is inverted, and the corresponding Timer
Y interrupt request bit is set to a “1”. The repeated in-
version of the CNTR1 pin output produces a
rectangular waveform with a duty ratio of 50 percent.
The initial level of the output is determined by the
CNTR1 polarity select bit (bit 6). When this bit is low,
the output starts from a high level. When this bit is
high, the output starts from a low level.
Pulse Period Measurement Mode
Count Source:
F/n (where n is 8, 16, 32, or 64).
This mode measures the period of the event wave-
form input to the CNTR1 pin.
CNTR1 Polarity Select Bit (TYM6) = “0”
When the falling edge of an event waveform is de-
tected on the CNTR1 pin, the contents of Timer Y
are stored in the temporary register that is as-
signed
the
same
address
as
Timer
Y.
Simultaneously, the value in the Timer Y reload
latch is transferred to Timer Y, and Timer Y contin-
ues counting down. The falling edge of an event
waveform also causes the CNTR1 interrupt re-
quest; therefore, the period of the event waveform
from falling edge to falling edge is found by read-
ing Timer Y in the CNTR1 interrupt routine. The
data read from Timer Y is the data previously
stored in its temporary register.
CNTR1 Polarity Select Bit (TYM6) = “1”
When the rising edge of an event waveform is de-
tected on the CNTR1 pin, the contents of Timer Y
are stored in the temporary register that is as-
signed
the
same
address
as
Timer
Y.
Simultaneously, the value in the Timer Y reload
latch is transferred to Timer Y, and Timer Y contin-
ues counting down.
The rising edge of an event waveform also causes
the CNTR1 interrupt request; therefore, the period
of the event waveform from rising edge to rising
edge is found by reading Timer Y in the CNTR1 in-
terrupt routine. The data read from Timer Y is the
data previously stored in its temporary register.
Each time the timer underflows, the Timer Y interrupt
request bit is set to a “1”, the contents of the timer re-
load latch are loaded into the timer, and the
countdown sequence begins again.
Event Counter Mode
Count Source: CNTR1
Timer countdown is triggered by input to the CNTR1
pin. Each time a timer underflows, the correspond-
ing timer interrupt request bit is set to a “1”, the
contents of the timer reload latch are loaded into the
timer, and the countdown sequence begins again.
The edge used to clock Timer Y is determined by
the CNTR1 polarity select bit (bit 6). When these
bits are “0”s, the timers are clocked on the rising
edge. When these bits are “1”s, the timers are
clocked on the falling edge
HL Pulse-width Measurement Mode
Count Source:
F/n (where n is 8, 16, 32, or 64).
This mode continuously measures both the logical
high pulse width and the logical low pulse width of
an event waveform input to the CNTR1 pin. When
the falling (or rising) edge of the event waveform is
detected on the CNTR1 pin, the contents of Timer Y
are stored in the temporary register that is assigned
the same address as Timer Y, regardless of the set-
ting of the CNTR1 polarity select bit. Simultaneously,
the value in the Timer Y reload latch is transferred to
Timer Y, which continues counting down. The falling
or rising edge of an event waveform causes the
CNTR1 interrupt request; therefore, the width of the
event waveform from the falling or rising edge to ris-
ing or falling edge is found by reading Timer Y in the
CNTR1 interrupt routine. The data read from Timer Y
is the data previously stored in its temporary regis-
ter.
Each time the timer underflows, the Timer Y interrupt
request bit is set to a “1”, the contents of the timer
reload latch are loaded into the timer, and the count-
down sequence begins again.
相關PDF資料 |
PDF描述 |
|---|---|
| M37643M8-XXXHP | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37643F8HP | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37700E2AFS | 16-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQCC80 |
| M37700E2AXXXFP | 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP80 |
| M37701E2-XXXSP | 16-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37640E8FS | 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37640M4T | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37640M8-111FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37640M8-126FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37640M8-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE CHIP 8 BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。