參數資料
型號： M306V5EESP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PDIP64
封裝： 0.750 INCH, PLASTIC, SDIP-64
文件頁數： 26/152頁
文件大小： 1963K
代理商： M306V5EESP
149
ATtiny25/45/85 [DATASHEET]
2586Q–AVR–08/2013
Notes:
2. Allows system clock to be output on pin. See “Clock Output Buffer” on page 31 for details.
3. The default value gives maximum start-up time for the default clock source. See Table 6-7 on page 28 for details.
4. The default setting selects internal, 8 MHz RC oscillator. See Table 6-6 on page 27 for details.
Note that fuse bits are locked if Lock Bit 1 (LB1) is programmed. Fuse bits should be programmed before lock bits.
The status of fuse bits is not affected by chip erase.
Lock bits can also be read by device firmware. See section “Reading Lock, Fuse and Signature Data from Soft-
20.2.1
Latching of Fuses
Fuse values are latched when the device enters programming mode and changes to fuse values will have no effect
until the part leaves programming mode. This does not apply to the EESAVE Fuse which takes effect once it is pro-
grammed. Fuses are also latched on power-up.
20.3
Device Signature Imprint Table
The device signature imprint table is a dedicated memory area used for storing miscellaneous device information,
such as the device signature and oscillator calibration data. Most of this memory segment is reserved for internal
use, as outlined in Table 20-6.
Notes:
1. See section “Signature Bytes” for more information.
2. See section “Calibration Bytes” for more information.
Table 20-5.
Fuse Low Byte
Fuse Low Byte
Bit No
Description
Default Value
CKDIV8 (1)
7
Clock divided by 8
0 (programmed)
CKOUT (2)
6
Clock output enabled
1 (unprogrammed)
SUT1 (3)
5
Start-up time setting
1 (unprogrammed)(3)
SUT0 (3)
4
Start-up time setting
0 (programmed)(3)
CKSEL3 (4)
3
Clock source setting
0 (programmed)(4)
CKSEL2 (4)
2
Clock source setting
0 (programmed)(4)
CKSEL1 (4)
1
Clock source setting
1 (unprogrammed)(4)
CKSEL0 (4)
0
Clock source setting
0 (programmed)(4)
Table 20-6.
Contents of Device Signature Imprint Table.
Address
High Byte
0x00
Signature byte 0 (1)
0x01
Calibration data for internal oscillator at 8.0 MHz (2)
0x02
Signature byte 1 (1)
0x03
Calibration data for internal oscillator at 6.4 MHz (2)
0x04
Signature byte 2 (1)
0x05 ... 0x2A
Reserved for internal use
相關PDF資料
PDF描述
M306V7FJAFP 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100
M306V7MJA-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100
M30833FJFP 32-BIT, FLASH, 30 MHz, MICROCONTROLLER, PQFP100
M30833MJFP 32-BIT, MROM, 30 MHz, MICROCONTROLLER, PQFP100
M30833MJGP 32-BIT, MROM, 30 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M306V5EESS 功能描述:EPROM MCU/M16C(TV/VTR) RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
M306V5ME 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M306V5ME-101SP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M306V5ME-105SPZ 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
M306V5ME-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*