- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN9117-MD (STANDARD MICROSYSTEMS CORP) HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER PDF資料下載
參數資料
| 型號： | LAN9117-MD |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER |
| 中文描述： | 1 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 82/131頁 |
| 文件大?。?/td> | 1531K |
| 代理商： | LAN9117-MD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁當前第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Revision 1.1 (05-17-05)
82
SMSC LAN9117
DATASHEET
5.3.9.1
Allowable settings for Configurable FIFO Memory Allocation
TX and RX FIFO space is configurable through the CSR - HW_CFG register defined above. The user
must select the FIFO allocation by setting the TX FIFO Size (TX_FIF_SZ) field in the hardware
configuration (HW_CFG) register. The TX_FIF_SZ field selects the total allocation for the TX data path,
including the TX Status FIFO size. The TX Status FIFO size is fixed at 512 Bytes (128 TX Status
DWORDs). The TX Status FIFO length is subtracted from the total TX FIFO size with the remainder
being the TX data FIFO Size. Note that TX data FIFO space includes both commands and payload
data.
4
Serial Management Interface Select (SMI_SEL
). This bit is used to switch
the SMI port (MDIO and MDC) between the internal PHY and the external
MII port. When this bit is cleared to ‘0’, the internal PHY is selected, and all
SMI transactions will be to the internal PHY. When this bit is set to ‘1’, the
external MII port is selected, and all SMI transactions will be to the external
PHY. This bit functions independent of EXT_PHY_EN. When this bit is set,
the internal MDIO and MDC signals are driven low. When this bit is cleared,
the external MIDIO signal is tri-stated, and the MDC signal is driven low.
Note:
This bit does not control the multiplexing of other MII signals.
R/W
0
3
External PHY Detect (EXT_PHY_DET)
. This bit reflects the latched value
of the EXT_PHY_DET strap. The EXT_PHY_DET strap is used to indicate
the presence of an external PHY. This strap is latched from the value of the
external MDIO signal upon power-up or hard reset. If MDIO is pulled high a
‘1’ will be seen in this bit. If MDIO is pulled low a ‘0’ will be seen in this bit.
The RXT_PHY_DET strap has no other effect on the internal logic. Its only
function is to give the system designer a mechanism to indicate the
presence of an external PHY to a software application.
RO
Dependant
on
EXT_PHY_D
ET strap pin
2
External PHY Enable (EXT_PHY_EN
). When set to a ‘1’, this bit enables
the external MII port. When cleared, the internal PHY is enabled and the
external MII port is disabled.
Notes:
■
This signal does not control multiplexing of the SMI port or the TX_CLK
or RX_CLK signals.
■
There are restrictions on the use of this bit. Please refer to
Section 3.12,
"MII Interface - External MII Switching," on page 43
for details.
RW
0
1
Soft Reset Timeout (SRST_TO)
.
If a software reset is attempted when the
internal PHY is not in the operational state (RX_CLK and TX_CLK running), the reset
will not complete and the soft reset operation will timeout and this bit will be set to a
‘1’. The host processor must correct the problem and issue another soft reset.
RO
0
0
Soft Reset (SRST)
. Writing 1 generates a software initiated reset. This reset
generates a full reset of the MAC CSR’s. The SCSR’s (system command
and status registers) are reset except for any NASR bits. Soft reset also
clears any TX or RX errors (TXE/RXE). This bit is self-clearing.
Notes:
■
Do not attempt a soft reset unless the internal PHY is fully awake and
operational. After a PHY reset, or when returning from a reduced power
state, the PHY must given adequate time to return to the operational state
before a soft reset can be issued. The internal RX_CLK and TX_CLK
signals must be running for a proper software reset. Please refer to
Section 6.8, "Reset Timing," on page 124
for details on PHY reset timing.
■
The LAN9117 must always be read at least once after power-up, reset, or
upon return from a power-saving state or write operations will not function.
SC
0
BITS
DESCRIPTION
TYPE
DEFAULT
相關PDF資料 |
PDF描述 |
|---|---|
| LAN9117-MT | HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER |
| LAN9118 | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN9118-MD | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN9118-MT | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN91C100-FD-SS | FEAST Fast Ethernet Controller with Full Duplex Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN9117-MT | 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN9118 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118_05 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118-MD | 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。