- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN9117-MD (STANDARD MICROSYSTEMS CORP) HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER PDF資料下載
參數資料
| 型號： | LAN9117-MD |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER |
| 中文描述： | 1 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 50/131頁 |
| 文件大小： | 1531K |
| 代理商： | LAN9117-MD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Revision 1.1 (05-17-05)
50
SMSC LAN9117
DATASHEET
TX COMMAND ‘B’
3.13.3
TX Data Format
The TX data section begins at the third DWORD in the TX buffer (after TX command ‘A’ and TX
command ‘B’). The location of the first byte of valid buffer data to be transmitted is specified in the
“Data Start Offset” field of the TX command ‘A’ word.
Table 3.13, "TX DATA Start Offset"
, shows the
correlation between the setting of the LSB’s in the “Data Start Offset” field and the byte location of the
first valid data byte. Additionally, transmit buffer data can be offset by up to 7 additional DWORDS as
indicated by the upper three MSB’s (5:2) in the “Data Start Offset” field.
TX data is contiguous until the end of the buffer. The buffer may end on a byte boundary. Unused
bytes at the end of the packet will not be sent to the MIL for transmission.
The Buffer End Alignment field in TX command ‘A’ specifies the alignment that must be maintained for
the associated buffer. End alignment may be specified as 4-, 16-, or 32-byte. The host processor is
responsible for adding the additional data to the end of the buffer. The hardware will automatically
remove this extra data.
3.13.3.1
TX Buffer Fragmentation Rules
Transmit buffers must adhere to the following rules:
■
Each buffer can start and end on any arbitrary byte alignment
■
The first buffer of any transmit packet can be any length
■
Middle buffers (i.e., those with First Segment = Last Segment = 0) must be greater than, or equal
to 4 bytes in length
■
The final buffer of any transmit packet can be any length
Table 3.12 TX Command 'B' Format
BITS
DESCRIPTION
31:16
Packet Tag.
The host should write a unique packet identifier to this field. This identifier is added to
the corresponding TX status word and can be used by the host to correlate TX status words with
their corresponding packets.
Note:
The use of packet tags is not required by the hardware. This field can be used by the LAN
software driver for any application. Packet Tags is one application example.
15:14
Reserved.
These bits are reserved. Always write zeros to this field to guarantee future compatibility.
13
Add CRC Disable.
When set, the automatic addition of the CRC is disabled.
12
Disable Ethernet Frame Padding.
When set, this bit prevents the automatic addition of padding to
an Ethernet frame of less than 64 bytes. The CRC field is also added despite the state of the Add
CRC Disable field.
11
Reserved.
These bits are reserved. Always write zeros to this field to guarantee future compatibility.
10:0
Packet Length (bytes).
This field indicates the total number of bytes in the current packet. This
length does not include the offset or padding. If the Packet Length field does not match the actual
number of bytes in the packet the Transmitter Error (TXE) flag will be set.
Table 3.13 TX DATA Start Offset
Data Start Offset [1:0]:
First TX Data Byte:
11
10
01
00
D[31:24]
D[23:16]
D[15:8]
D[7:0]
相關PDF資料 |
PDF描述 |
|---|---|
| LAN9117-MT | HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER |
| LAN9118 | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN9118-MD | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN9118-MT | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN91C100-FD-SS | FEAST Fast Ethernet Controller with Full Duplex Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN9117-MT | 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN9118 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118_05 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118-MD | 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。