- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN9117-MD (STANDARD MICROSYSTEMS CORP) HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER PDF資料下載
參數資料
| 型號： | LAN9117-MD |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER |
| 中文描述： | 1 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 43/131頁 |
| 文件大?。?/td> | 1531K |
| 代理商： | LAN9117-MD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
3.12
SMSC LAN9117
43
Revision 1.1 (05-17-05)
DATASHEET
MII Interface - External MII Switching
There are two mechanisms that are used to switch between the internal PHY and the external MII port.
■
A LAN driver or other software controlled mechanism is used to control the PHY_CLK_SEL[1:0]
bits described in
Section 5.3.9, "HW_CFG—Hardware Configuration Register"
that provides glitch-
free MII clock switching. This mechanism allows the host processor to disable (gate) the RX_CLK
and TX_CLK clocks from both the internal PHY and the external MII port, and switch the clock
sources once they have stopped. After switching the clocks, the LAN9117 transmitter and receiver
can be re-enabled.
■
A simple multiplexor that, with the exception of the SMI bus and the MII clocks, will switch the
remaining MII signals. This multiplexor is controlled by the EXT_PHY_EN bit described in
Section
5.3.9, "HW_CFG—Hardware Configuration Register"
3.12.1
SMI Switching
The Serial Management Interface (SMI) port can be switched between the internal PHY and external
MII ports based on the settings of the SMI_SEL bit described in
Section 5.3.9, "HW_CFG—Hardware
Configuration Register"
. The SMI port can be switched independent of the setting of the other MII
signals.
APPLICATION NOTE:
The user is cautioned to not switch the SMI port while an SMI transaction is in progress.
3.12.2
MII Clock Switching
The LAN9117 supports dynamic switching between the integrated internal PHY and the external MII
port which can connect to an external MII compatible Ethernet PHY device.
The remaining MII signals, with the exception of the SMI port, are switched using a simple multiplexor
controlled by the EXT_PHY_SEL bit described in
Section 5.3.9, "HW_CFG—Hardware Configuration
Register"
. It is required that the MII clocks be disabled before the other MII signals are switched.
The steps outlined in the flow diagram in Figure 3.12, "MII Switching Procedure", detail the required
procedure for switching the MII port, including the MII clocks. These steps must be followed in order
to guarantee clean switching of the MII ports.
Using the SMI interface, both the internal PHY, and the external PHY must be placed in a stable state.
For each device generating a TX_CLK or RX_CLK, this clock must be stable and glitch-free before the
switch can be made. If either device is not generating a TX_CLK or RX_CLK, this clock must remain
off until the switch is complete. In either case the TX_CLK and RX_CLK must be stable and glitch-free
for the device that will be selected after the switch. The following must be done prior to a switch:
■
The LAN9117 Transmitter must be halted.
■
The halting of the LAN9117 transmitter must be complete
■
The LAN9117 Receiver must be halted.
■
The halting of the LAN9117 receiver must be complete.
■
The PHY_CLK_SEL field must be set to 10b. This action will disable the MII clocks to the LAN9117
internal logic for both the internal PHY, and the external MII interface.
■
The host must wait a period of time not less than 5 cycles of the slowest operating clock before
executing the next step in this procedure.
APPLICATION NOTE:
For example, if the internal PHY was operating in 10Mbs mode, and the external PHY was
operating at 100Mbs mode, the internal PHY’s TX_CLK and RX_CLK period is the longest,
and will determine the required wait-time. In this case the TX_CLK and RX_CLK period for
the internal PHY is 400ns, therefore the host must wait 2us (5*400ns) before proceeding. If
the clocks of the device being deselected by the switch are not running, they are not
considered in this calculation.
相關PDF資料 |
PDF描述 |
|---|---|
| LAN9117-MT | HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER |
| LAN9118 | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN9118-MD | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN9118-MT | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN91C100-FD-SS | FEAST Fast Ethernet Controller with Full Duplex Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN9117-MT | 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN9118 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118_05 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118-MD | 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。