參數資料
型號： LAN83C185-JT
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 網絡接口
英文描述： HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER
中文描述： DATACOM, ETHERNET TRANSCEIVER, PQFP64
封裝： 10 X 10 MM, 1.40 MM HEIGHT, ROHS COMPLIANT, TQFP-64
文件頁數： 46/61頁
文件大小： 459K
代理商： LAN83C185-JT
High Performance Single Chip Low Power 10/100 Ethernet Physical Layer Transceiver (PHY)
Datasheet
Rev. 0.8 (11-16-04)
46
SMSC LAN83C185
DATASHEET
Figure 5.1 PHY Address Strapping on LEDS
The ACTIVITY LED output is driven active when CRS is active (high). When CRS becomes inactive,
the Activity LED output is extended by 128ms.
The
LINKON LED output is driven active whenever the PHY detects a valid link. The use of the
10Mbps or 100Mbps link test status is determined by the condition of the internally determined speed
selection.
The SPEED100 LED output is driven active when the operating speed is 100Mbit/s or during Auto-
negotiation. This LED will go inactive when the operating speed is 10Mbit/s or during line isolation
(register 31 bit 5).
The Full-Duplex LED output is driven active low when the link is operating in Full-Duplex mode.
5.4.8
Loopback Operation
The 10/100 digital has two independent loop-back modes: Internal loopback and far loopback.
5.4.8.1
Internal Loopback
The internal loopback mode is enabled by setting bit register 0 bit 14 to logic one. In this mode, the
scrambled transmit data (output of the scrambler) is looped into the receive logic (input of the
descrambler). The COL signal will be inactive in this mode, unless collision test (bit 0.7) is active.
In this mode, during transmission (TX_EN is HIGH), nothing is transmitted to the line and the
transmitters are powered down.
5.4.9
Configuration Signals
The PHY has 11 configuration signals whose inputs should be driven continuously, either by external
logic or external pull-up/pull-down resistors.
5.4.9.1
Physical Address Bus - PHYAD[4:0]
The PHYAD[4:0] signals are driven high or low to give each PHY a unique address. This address is
latched into an internal register at end of hardware reset. In a multi-PHY application (such as a
repeater), the controller is able to manage each PHY via the unique address. Each PHY checks each
management data frame for a matching address in the relevant bits. When a match is recognized, the
PHY responds to that particular frame. The PHY address is also used to seed the scrambler. In a multi-
PHY application, this ensures that the scramblers are out of synchronization and disperses the
electromagnetic radiation across the frequency spectrum.
LED1-LED4
~270 ohms
Phy Address = 0
LED output = active high
~10K ohms
~270 ohms
LED1-LED4
VDD
Phy Address = 1
LED output = active low
相關PDF資料
PDF描述
LAN8700 【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR TM in a Small Footprint
LAN9115 HIGHLY EFFICIENT SINGLE - CHIP 10/100 NON PCI ETHERNET CONTROLLER
LAN9115-MD HIGHLY EFFICIENT SINGLE - CHIP 10/100 NON PCI ETHERNET CONTROLLER
LAN9115-MT HIGHLY EFFICIENT SINGLE - CHIP 10/100 NON PCI ETHERNET CONTROLLER
LAN9116 Highly Efficient Single-Chip 10/100 Non-PCI Ethernet Controller
相關代理商/技術參數
參數描述
LAN83C795QFP WAF 制造商:SMSC 功能描述:
LAN8700 制造商:SMSC 制造商全稱:SMSC 功能描述:【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR TM in a Small Footprint
LAN8700AEZG 制造商:SMSC 功能描述:
LAN8700-AEZG 功能描述:以太網 IC HIPERFRM ETHRNT PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN8700C-AEZG 功能描述:以太網 IC IC w/HP Auto-MDIX Embedded Ethernet RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*