- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN83C185-JT (STANDARD MICROSYSTEMS CORP) HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER PDF資料下載
參數資料
| 型號： | LAN83C185-JT |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 網絡接口 |
| 英文描述： | HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER |
| 中文描述： | DATACOM, ETHERNET TRANSCEIVER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, ROHS COMPLIANT, TQFP-64 |
| 文件頁數： | 26/61頁 |
| 文件大小： | 459K |
| 代理商： | LAN83C185-JT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
High Performance Single Chip Low Power 10/100 Ethernet Physical Layer Transceiver (PHY)
Datasheet
Rev. 0.8 (11-16-04)
26
SMSC LAN83C185
DATASHEET
4.7.2
Re-starting Auto-negotiation
Auto-negotiation can be re-started at any time by setting register 0, bit 9. Auto-negotiation will also re-
start if the link is broken at any time. A broken link is caused by signal loss. This may occur because
of a cable break, or because of an interruption in the signal transmitted by the Link Partner. Auto-
negotiation resumes in an attempt to determine the new link configuration.
If the management entity re-starts Auto-negotiation by writing to bit 9 of the control register, the
LAN83C185 will respond by stopping all transmission/receiving operations. Once the break_link_timer
is done, in the Auto-negotiation state-machine (approximately 1200ms) the auto-negotiation will re-
start. The Link Partner will have also dropped the link due to lack of a received signal, so it too will
resume auto-negotiation.
4.7.3
Disabling Auto-negotiation
Auto-negotiation can be disabled by setting register 0, bit 12 to zero. The device will then force its
speed of operation to reflect the information in register 0, bit 13 (speed) and register 0, bit 8 (duplex).
The speed and duplex bits in register 0 should be ignored when auto-negotiation is enabled.
4.7.4
Half vs. Full Duplex
Half Duplex operation relies on the CSMA/CD (Carrier Sense Multiple Access / Collision Detect)
protocol to handle network traffic and collisions. In this mode, the carrier sense signal, CRS, responds
to both transmit and receive activity. In this mode, If data is received while the PHY is transmitting,
a collision results.
In Full Duplex mode, the PHY is able to transmit and receive data simultaneously. In this mode, CRS
responds only to receive activity. The CSMA/CD protocol does not apply and collision detection is
disabled.
4.8
PHY Management Control
The Management Control module includes 3 blocks:
■
Serial Management Interface (SMI)
■
Management Registers Set
■
Interrupt
4.8.1
Serial Management Interface (SMI)
The Serial Management Interface is used to control the LAN83C185 and obtain its status. This
interface supports registers 0 through 6 as required by Clause 22 of the 802.3 standard, as well as
“vendor-specific” registers 16 to 31 allowed by the specification. Non-supported registers (7 to 15) will
be read as hexadecimal “FFFF”.
At the system level there are 2 signals, MDIO and MDC where MDIO is bi-directional open-drain and
MDC is the clock.
A special feature (enabled by register 17 bit 3) forces the PHY to disregard the PHY-Address in the
SMI packet causing the PHY to respond to any address. This feature is useful in multi-PHY
applications and in production testing, where the same register can be written in all the PHYs using a
single write transaction.
The MDC signal is an aperiodic clock provided by the station management controller (SMC). The MDIO
signal receives serial data (commands) from the controller SMC, and sends serial data (status) to
the SMC. The minimum time between edges of the MDC is 160 ns. There is no maximum time
between edges.
相關PDF資料 |
PDF描述 |
|---|---|
| LAN8700 | 【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR TM in a Small Footprint |
| LAN9115 | HIGHLY EFFICIENT SINGLE - CHIP 10/100 NON PCI ETHERNET CONTROLLER |
| LAN9115-MD | HIGHLY EFFICIENT SINGLE - CHIP 10/100 NON PCI ETHERNET CONTROLLER |
| LAN9115-MT | HIGHLY EFFICIENT SINGLE - CHIP 10/100 NON PCI ETHERNET CONTROLLER |
| LAN9116 | Highly Efficient Single-Chip 10/100 Non-PCI Ethernet Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN83C795QFP WAF | 制造商:SMSC 功能描述: |
| LAN8700 | 制造商:SMSC 制造商全稱:SMSC 功能描述:【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR TM in a Small Footprint |
| LAN8700AEZG | 制造商:SMSC 功能描述: |
| LAN8700-AEZG | 功能描述:以太網 IC HIPERFRM ETHRNT PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN8700C-AEZG | 功能描述:以太網 IC IC w/HP Auto-MDIX Embedded Ethernet RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。