參數資料
型號： IDT82P5088BBG
廠商： IDT, Integrated Device Technology Inc
文件頁數： 59/81頁
文件大?。?/td> 0K
描述： IC LIU T1/E1/J1 OCTAL 256PBGA
標準包裝： 90
功能： 線路接口單元（LIU）
接口： E1，J1，T1
電路數： 8
電源電壓： 1.8V, 3.3V
功率（瓦特）： 2.57W
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 256-BGA
供應商設備封裝： 256-PBGA（17x17）
包裝： 托盤
包括： 集成式時鐘適配器
IDT82P5088
UNIVERSAL OCTAL T1/E1/J1 LIU WITH INTEGRATED CLOCK ADAPTER
IEEE STD 1149.1 JTAG TEST ACCESS PORT
62
February 5, 2009
5.2.4
TEST ACCESS PORT CONTROLLER
The TAP controller is a 16-state synchronous state machine. Figure-24
shows its state diagram following the description of each state. Note that
the figure contains two main branches to access either the data or instruc-
tion registers. The value shown next to each state transition in this figure
states the value present at TMS at each rising edge of TCK. Please refer
to Table-70 for details of the state description.
Table-70 TAP Controller State Description
STATE
DESCRIPTION
Test Logic Reset
In this state, the test logic is disabled. The device is set to normal operation. During initialization, the device initializes the instruction register
with the IDCODE instruction. Regardless of the original state of the controller, the controller enters the Test-Logic-Reset state when the
TMS input is held high for at least 5 rising edges of TCK. The controller remains in this state while TMS is high. The device processor auto-
matically enters this state at power-up.
Run-Test/Idle
This is a controller state between scan operations. Once in this state, the controller remains in the state as long as TMS is held low. The
instruction register and all test data registers retain their previous state. When TMS is high and a rising edge is applied to TCK, the control-
ler moves to the Select-DR state.
Select-DR-Scan
This is a temporary controller state and the instruction does not change in this state. The test data register selected by the current instruc-
tion retains its previous state. If TMS is held low and a rising edge is applied to TCK when in this state, the controller moves into the Cap-
ture-DR state and a scan sequence for the selected test data register is initiated. If TMS is held high and a rising edge applied to TCK, the
controller moves to the Select-IR-Scan state.
Capture-DR
In this state, the Boundary Scan Register captures input pin data if the current instruction is EXTEST or SAMPLE/PRELOAD. The instruc-
tion does not change in this state. The other test data registers, which do not have parallel input, are not changed. When the TAP controller
is in this state and a rising edge is applied to TCK, the controller enters the Exit1-DR state if TMS is high or the Shift-DR state if TMS is low.
Shift-DR
In this controller state, the test data register connected between TDI and TDO as a result of the current instruction shifts data on stage
toward its serial output on each rising edge of TCK. The instruction does not change in this state. When the TAP controller is in this state
and a rising edge is applied to TCK, the controller enters the Exit1-DR state if TMS is high or remains in the Shift-DR state if TMS is low.
Exit1-DR
This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-DR
state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Pause-DR
state. The test data register selected by the current instruction retains its previous value and the instruction does not change during this
state.
Pause-DR
The pause state allows the test controller to temporarily halt the shifting of data through the test data register in the serial path between TDI
and TDO. For example, this state could be used to allow the tester to reload its pin memory from disk during application of a long test
sequence. The test data register selected by the current instruction retains its previous value and the instruction does not change during this
state. The controller remains in this state as long as TMS is low. When TMS goes high and a rising edge is applied to TCK, the controller
moves to the Exit2-DR state.
Exit2-DR
This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-DR
state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Shift-DR
state. The test data register selected by the current instruction retains its previous value and the instruction does not change during this
state.
Update-DR
The Boundary Scan Register is provided with a latched parallel output to prevent changes while data is shifted in response to the EXTEST
and SAMPLE/PRELOAD instructions. When the TAP controller is in this state and the Boundary Scan Register is selected, data is latched
into the parallel output of this register from the shift-register path on the falling edge of TCK. The data held at the latched parallel output
changes only in this state. All shift-register stages in the test data register selected by the current instruction retain their previous value and
the instruction does not change during this state.
Select-IR-Scan
This is a temporary controller state. The test data register selected by the current instruction retains its previous state. If TMS is held low
and a rising edge is applied to TCK when in this state, the controller moves into the Capture-IR state, and a scan sequence for the instruc-
tion register is initiated. If TMS is held high and a rising edge is applied to TCK, the controller moves to the Test-Logic-Reset state. The
instruction does not change during this state.
Capture-IR
In this controller state, the shift register contained in the instruction register loads a fixed value of '100' on the rising edge of TCK. This sup-
ports fault-isolation of the board-level serial test data path. Data registers selected by the current instruction retain their value and the
instruction does not change during this state. When the controller is in this state and a rising edge is applied to TCK, the controller enters
the Exit1-IR state if TMS is held high, or the Shift-IR state if TMS is held low.
Shift-IR
In this state, the shift register contained in the instruction register is connected between TDI and TDO and shifts data one stage towards its
serial output on each rising edge of TCK. The test data register selected by the current instruction retains its previous value and the instruc-
tion does not change during this state. When the controller is in this state and a rising edge is applied to TCK, the controller enters the Exit1-
IR state if TMS is held high, or remains in the Shift-IR state if TMS is held low.
相關PDF資料
PDF描述
IDT82V2041EPPG IC LIU T1/J1/E1 1CH 44-TQFP
IDT82V2042EPFG IC LIU T1/J1/E1 2CH SHORT 80TQFP
IDT82V2044EPFG IC LIU T1/E1 QUAD SHORT 128-TQFP
IDT82V2048DAG IC LIU T1/E1 8CH SHORT 144-TQFP
IDT82V2048EDR IC LIU T1/E1 8CH SHORT 208-TQFP
相關代理商/技術參數
參數描述
IDT82P5088BBG8 制造商:Integrated Device Technology Inc 功能描述:IC LIU T1/E1/J1 OCTAL 256PBGA
IDT82V1054A 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:QUAD PROGRAMMABLE PCM CODEC WITH MPI INTERFACE
IDT82V1054APF 功能描述:IC PCM CODEC 4CH MPI 3.3V 64TQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
IDT82V1054APF8 功能描述:IC PCM CODEC 4CH MPI 3.3V 64TQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
IDT82V1054APFG 功能描述:IC PCM CODEC 4CH MPI 3.3V 64TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*