參數資料
型號： GS9064
元件分類： 通信、網絡模塊及開發工具
英文描述： Telecomm/Datacomm
中文描述： 電信/數據通信
文件頁數： 37/47頁
文件大?。?/td> 754K
代理商： GS9064
GENNUM CORPORATION
22208 - 0
37 of 47
G
3.10.5.3 Lock Error Detection
The LOCKED pin of the GS9060 indicates the lock status of
the reclocker and lock detect blocks of the device. Only
when the LOCKED pin is asserted HIGH has the device
correctly locked to the received data stream, (see Section
3.6).
The GS9060 will also indicate lock error to the host interface
when LOCKED = LOW by setting the LOCK_ERR bit in the
ERROR_STATUS register HIGH.
3.10.5.4 Ancillary Data Checksum Error Detection
The GS9060 will calculate checksums for all received
ancillary data and compare the calculated values to the
received checksum words. If a mismatch is detected, the
error is flagged in the CS_ERR bits of the ERROR_STATUS
register.
Although the GS9060 will calculate and compare checksum
values for all ancillary data types by default, the host
interface may program the device to check only certain
types of ancillary data checksums.
This is accomplished via the ANC_TYPE register as
described in Section 3.10.2.1.
3.10.5.5 TRS Error Detection
TRS errors flags are generated by the GS9060 when:
1. The received TRS timing does not correspond to the
internal flywheel timing; or
2. The received TRS hamming codes are incorrect.
Both 8-bit and 10-bit SAV and EAV TRS words are checked
for timing and data integrity errors. These are flagged via
the SAV_ERR and/or EAV_ERR bits of the ERROR_STATUS
register.
Timing-based TRS errors will only be generated if the
FW_EN/DIS pin is set HIGH.
3.10.6 Error Correction and Insertion
In addition to signal error detection and indication, the
GS9060 may also correct certain types of errors by
inserting corrected code words and checksums into the
data stream. These features are only available in SMPTE
mode and IOPROC_EN/DIS must be set HIGH. Individual
correction features may be enabled or disabled via the
IOPROC_DISABLE register (Table 13).
All of the IOPROC_DISABLE register bits default to '0' after
device reset, enabling all of the processing features. To
disable any individual error correction feature, the host
interface must set the corresponding bit HIGH in the
IOPROC_DISABLE register.
TABLE 13 HOST INTERFACE DESCRIPTION FOR INTERNAL PROCESSING DISABLE REGISTER
REGISTER NAME
BIT
BIT NAME
DESCRIPTION
R/W
DEFAULT
IOPROC_DISABLE
Address: 00h
15-9
Not Used
8
H_CONFIG
Horizontal sync timing output configuration. Set LOW for
active line blanking timing. Set HIGH for H blanking
based on the H bit setting of the TRS words. See Figure
9.
0
7
Not Used
6
Not Used
5
ILLEGAL_REMAP
Illegal Code re-mapping. Correction of illegal code
words within the active picture. Set HIGH to disable. The
IOPROC_EN/DIS pin must be set HIGH.
R/W
0
4
EDH_CRC_INS
Error Detection & Handling (EDH) Cyclical Redundancy
Check (CRC) error correction insertion. Set HIGH to
disable. The IOPROC_EN/DIS pin must be set HIGH.
R/W
0
3
ANC_CSUM_INS
Ancillary Data Check-sum insertion. Set HIGH to
disable. The IOPROC_EN/DIS pin must be set HIGH.
R/W
0
2-1
Not Used
0
TRS_INS
Timing Reference Signal Insertion. Set HIGH to disable.
The IOPROC_EN/DIS pin must be set HIGH.
R/W
0
相關PDF資料
PDF描述
GSA1 Fuse
GSA1.25 Fuse
GSA1.6 Fuse
GSA10 Fuse
GSA750 Fuse
相關代理商/技術參數
參數描述
GS9064A 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GS9064A HD-LINX㈢ II Adaptive Cable Equalizer
GS9064ACKDE3 制造商:Semtech Corporation 功能描述:Adaptive Cable Equalizer. High-speed BiCMOS integrated circuit. 16-Pin SOIC 制造商:Semtech Corporation 功能描述:SD/ASI Adaptive Equalizer
GS9064ACTDE3 制造商:Semtech Corporation 功能描述:SD/ASI Adaptive Equalizer
GS9064-CKD 制造商:Rochester Electronics LLC 功能描述: 制造商:Gennum Corporation 功能描述:
GS9064-CKDE3 制造商:Gennum Corporation 功能描述:Cable Equalizer 16-Pin SOIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*