參數資料
型號: EVAL-ADUC832QSZ
廠商: Analog Devices Inc
文件頁數: 81/92頁
文件大?。?/td> 0K
描述: KIT DEV FOR ADUC832 QUICK START
產品培訓模塊: Process Control
標準包裝: 1
系列: QuickStart™ 套件
類型: MCU
適用于相關產品: ADuC832
所含物品: 評估板,線纜,電源,軟件和文檔
其它名稱: EVAL-ADUC832QS
EVAL-ADUC832QS-ND
ADuC832
Data Sheet
Rev. B | Page 82 of 92
ADUC832 HARDWARE DESIGN CONSIDERATIONS
This section outlines some of the key hardware design
considerations that must be addressed when integrating the
ADuC832 into any hardware system.
CLOCK OSCILLATOR
The clock source for the ADuC832 can be generated by the
internal PLL or by an external clock input. To use the internal
PLL, connect a 32.768 kHz parallel resonant crystal between
XTAL1 and XTAL2, and connect a capacitor from each pin to
ground as shown in Figure 85. This crystal allows the PLL to
lock correctly to give a fVCO of 16.78 MHz. If no crystal is present,
the PLL free runs, giving a fVCO of 16.7 MHz ± 20%. This is
useful if an external clock input is required. The part powers up
and the PLL free runs; the user can then write to the CFG832
SFR in the software to enable the external clock input on P3.4.
XTAL2
XTAL1
TO INTERNAL
TIMING CIRCUITS
ADuC832
02
98
7-
0
73
Figure 85. External Parallel Resonant Crystal Connections
P3.4
TO INTERNAL
TIMING CIRCUITS
ADuC832
EXTERNAL
CLOCK
SOURCE
02
98
7-
0
74
Figure 86. Connecting an External Clock Source
Whether using the internal PLL or an external clock source, the
ADuC832 specified operational clock speed range is 400 kHz to
16.78 MHz. The core itself is static, and functions all the way
down to dc. However, at clock speeds slower than 400 kHz, the
ADC no longer functions correctly. Therefore, to ensure specified
operation, use a clock frequency of at least 400 kHz and no
more than 16.78 MHz.
EXTERNAL MEMORY INTERFACE
In addition to its internal program and data memories, the
ADuC832 can access up to 64 kB of external program memory
(such as ROM and PROM) and up to 16 MB of external data
memory (SRAM).
To select from which code space (internal or external program
memory) to begin executing instructions, tie the EA (external
access) pin high or low, respectively. When EA is high (pulled
up to DVDD), the user program execution starts at Address 0 of
the internal 62 kB of Flash/EE code space. When EA is low (tied
to ground), the user program execution starts at Address 0 of
the external code space.
A second very important function of the EA pin is described in
the Single Pin Emulation Mode section.
External program memory (if used) must be connected to the
ADuC832 as illustrated in Figure 87. Note that 16 I/O lines
(Port 0 and Port 2) are dedicated to bus functions during
external program memory fetches. Port 0 (P0) serves as a
multiplexed address/data bus. It emits the low byte of the
program counter as an address, and then goes into a float state
awaiting the arrival of the code byte from the program memory.
During the time that the low byte of the program counter is
valid on P0, the signal address latch enable (ALE) clocks this
byte into an address latch. Meanwhile, Port 2 (P2) emits the
high byte of the program counter, then PSEN strobes the
EPROM and the code byte is read into the ADuC832.
LATCH
EPROM
OE
A8 TO A15
A0 TO A7
D0 TO D7
(INSTRUCTION)
ADuC832
PSEN
P2
ALE
P0
02
98
7-
07
5
Figure 87. External Program Memory Interface
Note that program memory addresses are always 16 bits wide,
even in cases where the actual amount of program memory
used is less than 64 kB. External program execution sacrifices two
of the 8-bit ports (P0 and P2) to the function of addressing the
program memory. While executing from external program
memory, Port 0 and Port 2 can be used simultaneously for
read/write access to external data memory, but not for general-
purpose I/O.
Though both external program memory and external data
memory are accessed by some of the same pins, the two are
completely independent of each other from a software point
of view. For example, the chip can read/write external data
memory while executing from external program memory.
Figure 88 shows a hardware configuration for accessing up to
64 kB of external RAM. This interface is standard to any 8051-
compatible MCU.
相關PDF資料
PDF描述
HBM15DRXS CONN EDGECARD 30POS DIP .156 SLD
PCX1H270MCL1GS CAP ALUM 27UF 50V 20% SMD
HSM08DRKI CONN EDGECARD 16POS DIP .156 SLD
0210490857 CABLE JUMPER 1.25MM .051M 17POS
EVAL-ADUC831QSZ KIT DEV FOR ADUC831 QUICK START
相關代理商/技術參數
參數描述
EVAL-ADUC834QS 制造商:Analog Devices 功能描述:DATA ACQ SYS, MICROCNVRTR, DUAL 16BIT/24BIT - ADCS W/ EMBEDD - Bulk 制造商:Analog Devices 功能描述:8052 ADUC834 QUICKSTART DEV KIT
EVAL-ADUC834QSZ 功能描述:KIT DEV QUICK START ADUC834 RoHS:是 類別:編程器,開發系統 >> 通用嵌入式開發板和套件(MCU、DSP、FPGA、CPLD等) 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206,PIC16F690,PIC16F819 所含物品:板,線纜,元件,CD,PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
EVAL-ADUC836QS 制造商:Analog Devices 功能描述:MCU 8BIT 8052 CISC 62KB+4KB FLASH 3.6V 48LQFP - Bulk 制造商:Analog Devices 功能描述:KIT- ADUC836 DEV SYSTEM
EVAL-ADUC841QS 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
EVAL-ADUC841QSP2 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU