- 您現在的位置：買賣IC網 > PDF目錄377000 > DSP1629 TVS 400W 64V UNIDIRECT SMA PDF資料下載
參數資料
| 型號： | DSP1629 |
| 英文描述： | TVS 400W 64V UNIDIRECT SMA |
| 中文描述： | DSP1629數字信號處理器 |
| 文件頁數： | 66/126頁 |
| 文件大?。?/td> | 1993K |
| 代理商： | DSP1629 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
Data Sheet
March 2000
DSP1629 Digital Signal Processor
66
Lucent Technologies Inc.
6 Signal Descriptions
(continued)
6.4 Parallel Host Interface or Serial Interface
#2 and Control I/O Interface
This interface pin multiplexes a parallel host interface
with a second serial I/O interface and a 4-bit I/O inter-
face. The interface selection is made by writing the
ESIO2 bit in the ioc register (see Table 38 and Section
4.1). The functions and signals for the second SIO cor-
respond exactly with those in SIO #1. Therefore, the pin
descriptions below discuss only PHIF and BIO pin func-
tionality.
PB[7:0]
Parallel I/O Data Bus:
This 8-bit bidirectional bus is
used to input data to, or output data from, the PHIF.
Note that PB[3:0] are pin multiplexed with SIO2 func-
tionality, and PB[7:4] are pin multiplexed with BIO unit
pins IOBIT[3:0] (see Section 4.1).
PCSN
Peripheral Chip Select Not:
Negative assertion. PCSN
is an input. While PCSN is low, the data strobes PIDS
and PODS are enabled. While PCSN is high, the
DSP1629 ignores any activity on PIDS and PODS.
PBSEL
Peripheral Byte Select:
An input pin, configurable in
software. Selects the high or low byte of pdx0 available
for host accesses.
PSTAT
Peripheral Status Select:
PSTAT is an input. When a
logic 0, the PHIF will output the pdx0[out] register on the
PB bus. When a logic 1, the PHIF will output the con-
tents of the PSTAT register on PB[7:0].
PIDS
Parallel Input Data Strobe:
An input pin, software con-
figurable to support both Inteland Motorola protocols.
In Intelmode: Negative assertion. PIDS is pulled low by
an external device to indicate that data is available on
the PB bus. The DSP latches data on the PB bus on the
rising edge (low-to-high transition) of PIDS or PCSN,
whichever comes first.
In Motorolamode: PIDS/PRWN functions as a read/
write strobe. The external device sets PIDS/PRWN to a
logic 0 to indicate that data is available on the PB bus
(write operation by the external device). A logic 1 on
PIDS/PRWN indicates an external read operation by the
external device.
PODS
Parallel Output Data Strobe:
An input pin, software
configurable to support both Intel and Motorola proto-
cols.
In Intelmode: Negative assertion. When PODS is pulled
low by an external device, the DSP1629 places the con-
tents of the parallel output register, pdx0, onto the PB
bus.
In Motorolamode: Software-configurable assertion lev-
el. The external device uses PODS/PDS as its data
strobe for both read and write operations.
PIBF
Parallel Input Buffer Full:
An output pin with positive
assertion; configurable in software. This flag is cleared
after reset, indicating an empty input buffer pdx0[in].
PIBF is set immediately after the rising edge of PIDS or
PCSN, indicating that data has been latched into the
pdx0[in] register. When the DSP1629 reads the con-
tents of this register, emptying the buffer, the flag is
cleared.
Configured in software, PIBF may become the logical
OR of the PIBF and POBE flags.
POBE
Parallel Output Buffer Empty:
An output pin with pos-
itive assertion; configurable in software. This flag is set
after reset, indicating an empty output buffer pdx0[out].
POBE is set immediately after the rising edge of PODS
or PCSN, indicating that the data in pdx0[out] has been
driven onto the PB bus. When the DSP1629 writes to
pdx0[out], filling the buffer, this flag is cleared.
6.5 Control I/O Interface
This interface is used for status and control operations
provided by the bit I/O unit of the DSP1629. It is pin mul-
tiplexed with the PHIF and VEC[3:0] pins (see Section
4.1). Setting the ESIO2 and EBIOH bits in the ioc regis-
ter provides a full 8-bit BIO interface at the associated
pins.
IOBIT[7:0]
I/O Bits [7:0]:
Each of these bits can be independently
configured as either an input or an output. As outputs,
they can be independently set, toggled, or cleared. As
inputs, they can be tested independently or in combina-
tions for various data patterns.
相關PDF資料 |
PDF描述 |
|---|---|
| DSP16410C | TVS 400W 7.0V UNIDIRECT SMA |
| DSP16410 | 16-bit fixed point DSP with Flash |
| DSP25-16AR | Phase-leg Rectifier Diode |
| DSP25 | Phase-leg Rectifier Diode |
| DSP25-12A | Phase-leg Rectifier Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSP1629BA10K10IT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP|16-BIT|CMOS|BGA|144PIN|PLASTIC |
| DSP1629BA10K12.5IR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital Signal Processor |
| DSP1629BA10K16.7IT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP|16-BIT|CMOS|BGA|144PIN|PLASTIC |
| DSP1629BA10K19.2IR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital Signal Processor |
| DSP1629BA16K10IT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DSP|16-BIT|CMOS|BGA|144PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。