- 您現在的位置：買賣IC網 > PDF目錄385273 > DS2154 (Maxim Integrated Products, Inc.) Enhanced E1 Single Chip Transceiver(改進型E1單片收發器) PDF資料下載
參數資料
| 型號： | DS2154 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Enhanced E1 Single Chip Transceiver(改進型E1單片收發器) |
| 中文描述： | 增強型E1單芯片收發器 |
| 文件頁數： | 25/71頁 |
| 文件大?。?/td> | 654K |
| 代理商： | DS2154 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
DS2154
071498 25/71
RCLA
CCR3.0
Receive Carrier Loss (RCL) Alternate Criteria.
0=RCL declared upon 255 consecutive zeros (125 us)
1=RCL declared upon 2048 consecutive zeros (1 ms)
POWER–UP SEQUENCE
On power–up, after the supplies are stable, the DS2154
should be configured for operation by writing to all of the
internal registers (this includes the Test Registers) since
the contents of the internal registers cannot be pre-
dicted on power–up. Next, the LIRST (CCR5.7) bit
should be toggled from zero to one to reset the line inter-
face circuitry (it will take the DS2154 about 40 ms to
recover from the LIRST bit being toggled). Finally, after
the RSYSCLK and TSYSCLK inputs are stable, the
ESR bit should be toggled from a zero to a one and then
back to zero (this step can be skipped if the elastic
stores are not being used). Both TCLK and RCLKI must
be present for the parallel control port to operate
properly.
CCR4: COMMON CONTROL REGISTER 4
(Address=A8 Hex)
(MSB)
(LSB)
RLB
LLB
LIAIS
TCM4
TCM3
TCM2
TCM1
TCM0
SYMBOL
POSITION
NAME AND DESCRIPTION
RLB
CCR4.7
Remote Loopback.
0=loopback disabled
1= loopback enabled
LLB
CCR4.6
Local Loopback.
0=loopback disabled
1=loopback enabled
LIAIS
CCR4.5
Line Interface AIS Generation Enable.
See Figure 1–1 for details.
0=allow normal data from TPOSI/TNEGI to be transmitted at TTIP and
TRING
1=force unframed all ones to be transmitted at TTIP and TRING
TCM4
CCR4.4
Transmit Channel Monitor Bit 4.
MSB of a channel decode that deter-
mines which transmit channel data will appear in the TDS0M register. See
Section 6 for details.
TCM3
CCR4.3
Transmit Channel Monitor Bit 3.
TCM2
CCR4.2
Transmit Channel Monitor Bit 2.
TCM1
CCR4.1
Transmit Channel Monitor Bit 1.
TCM0
CCR4.0
Transmit Channel Monitor Bit 0.
LSB of the channel decode.
REMOTE LOOPBACK
When CCR4.7 is set to a one, the DS2154 will be forced
into Remote LoopBack (RLB). In this loopback, data
input via the RPOSI and RNEGI pins will be transmitted
back to the TPOSO and TNEGO pins. Data will con-
tinue to pass through the receive side framer of the
DS2154 as it would normally and the data from the
transmit side formatter will be ignored. Please see
Figure 1–1 for more details.
LOCAL LOOPBACK
When CCR4.6 is set to a one, the DS2154 will be forced
into Local LoopBack (LLB). In this loopback, data will
continue to be transmitted as normal through the trans-
mit side of the DS2154. Data being received at RTIP
and RRING will be replaced with the data being trans-
mitted. Data in this loopback will pass through the jitter
attenuator. Please see Figure 1–1 for more details.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2164Q | G.726 ADPCM Processor(G.726自適應音頻脈沖編碼處理器) |
| DS2175 | T1/CEPT Elastic Store(T1/CEPT 彈性存儲器) |
| DS2180A | T1 Transceiver(T1收發器) |
| DS2187 | Receive Line Interface(接收線接口) |
| DS2250T | Soft Microcontroller Module(軟件微控制器模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2154DK | 功能描述:KIT DESIGN E1 DS2154 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| DS2154L | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154L+ | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154LA2 | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2154LA2+ | 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。