參數資料
型號： DS2154
廠商： Maxim Integrated Products, Inc.
英文描述： Enhanced E1 Single Chip Transceiver(改進型E1單片收發器)
中文描述： 增強型E1單芯片收發器
文件頁數： 11/71頁
文件大小： 654K
代理商： DS2154
DS2154
071498 11/71
Receive Channel Clock [RCHCLK].
256 KHz clock
which pulses high during the LSB of each channel.
Synchronous with RCLK when the receive side elastic
store is disabled. Synchronous with RSYSCLK when
the receive side elastic store is enabled. Useful for par-
allel to serial conversion of channel data.
Receive Channel Block [RCHBLK].
A user program-
mable output that can be forced high or low during any of
the 32 E1 channels. Synchronous with RCLK when the
receive side elastic store is disabled. Synchronous with
RSYSCLK when the receive side elastic store is
enabled. Useful for blocking clocks to a serial UART or
LAPD controller in applications where not all E1 chan-
nels are used such as Fractional E1, 384K bps service,
768K bps, or ISDN–PRI. Also useful for locating individ-
ual channels in drop–and–insert applications, for exter-
nal per–channel loopback, and for per–channel condi-
tioning. See Section 9 for details.
Receive Serial Data [RSER].
Received NRZ serial
data. Updated on rising edges of RCLK when the
receive side elastic store is disabled. Updated on the
rising edges of RSYSCLK when the receive side elastic
store is enabled.
Receive Sync [RSYNC].
An extracted pulse, one
RCLK wide, is output at this pin which identifies either
frame or CAS/CRC multiframe boundaries. If the
receive side elastic store is enabled, then this pin can be
enabled to be an input at which a frame or multiframe
boundary pulse synchronous with RSYSCLK is applied.
Receive Frame Sync [RFSYNC].
An extracted 8 KHz
pulse, one RCLK wide, is output at this pin which identi-
fies frame boundaries.
Receive Multiframe Sync [RMSYNC].
An extracted
pulse, one RSYSCLK wide, is output at this pin which
identifies multiframe boundaries. If the receive side
elastic store is disabled, then this output will output mul-
tiframe boundaries associated with RCLK.
Receive Data [RDATA].
Updated on the rising edge of
RCLK with the data out of the receive side framer.
Receive System Clock [RSYSCLK].
1.544 MHz or
2.048 MHz clock. Only used when the elastic store
function is enabled. Should be tied low in applications
that do not use the elastic store. Can be burst at rates up
to 8.192 MHz.
Receive Signaling Output [RSIG].
Outputs signaling
bits in a PCM format. Updated on rising edges of RCLK
when the receive side elastic store is disabled. Updated
on the rising edges of RSYSCLK when the receive side
elastic store is enabled. See Section 13 for timing
examples.
Receive Loss of Sync / Loss of Transmit Clock
[RLOS/LOTC].
A dual function output that is controlled
by the TCR2.0 control bit. This pin can be programmed
to either toggle high when the synchronizer is searching
for the frame and multiframe or to toggle high if the TCLK
pin has not been toggled for 5
μ
s.
Receive Carrier Loss [RCL].
Set high when the line
interface detects a loss of carrier. [Note: a test mode
exists to allow the DS2154 to detect carrier loss at
RPOSI and RNEGI in place of detection at RTIP and
RRING].
Receive Signaling Freeze [RSIGF].
Set high when the
signaling data is frozen via either automatic or manual
intervention. Used to alert downstream equipment of
the condition.
8 MHz Clock [8MCLK].
8.192 MHz output clock that is
referenced to the clock that is output at the RCLK pin.
Receive Positive Data Output [RPOSO].
Updated on
the rising edge of RCLKO with the bipolar data out of the
line interface. This pin is normally tied to RPOSI.
Receive Negative Data Output [RNEGO].
Updated
on the rising edge of RCLKO with the bipolar data out of
the line interface. This pin is normally tied to RNEGI.
Receive Clock Output [RCLKO].
Buffered recovered
clock from the E1 line. This pin is normally tied to
RCLKI.
Receive Positive Data Input [RPOSI].
Sampled on
the falling edge of RCLKI for data to be clocked through
the receive side framer. RPOSI and RNEGI can be tied
together for a NRZ interface. Can be internally con-
nected to RPOSO by tying the LIUC pin high.
Receive Negative Data Input [RNEGI].
Sampled on
the falling edge of RCLKI for data to be clocked through
the receive side framer. RPOSI and RNEGI can be tied
together for a NRZ interface. Can be internally con-
nected to RNEGO by tying the LIUC pin high.
相關PDF資料
PDF描述
DS2164Q G.726 ADPCM Processor(G.726自適應音頻脈沖編碼處理器)
DS2175 T1/CEPT Elastic Store(T1/CEPT 彈性存儲器)
DS2180A T1 Transceiver(T1收發器)
DS2187 Receive Line Interface(接收線接口)
DS2250T Soft Microcontroller Module(軟件微控制器模塊)
相關代理商/技術參數
參數描述
DS2154DK 功能描述:KIT DESIGN E1 DS2154 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
DS2154L 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154L+ 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LA2 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2154LA2+ 功能描述:網絡控制器與處理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*