- 您現在的位置：買賣IC網 > PDF目錄378513 > CY7C954DX (Cypress Semiconductor Corp.) ATM HOTLink Transceiver(ATM 熱接插收發器) PDF資料下載
參數資料
| 型號： | CY7C954DX |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | ATM HOTLink Transceiver(ATM 熱接插收發器) |
| 中文描述： | 自動柜員機的HOTLink收發器（自動柜員機熱接插收發器） |
| 文件頁數： | 34/42頁 |
| 文件大小： | 484K |
| 代理商： | CY7C954DX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
CY7C954DX
PRELIMINARY
34
X3.230 Codes and Notation Conventions
Information to be transmitted over a serial link is encoded eight
bits at a time into a 10-bit Transmission Character and then
sent serially, bit by bit. Information received over a serial link is
collected ten bits at a time, and those Transmission Characters
that are used for data (Data Characters) are decoded into the
correct eight-bit codes. The 10-bit Transmission Code sup-
ports all 256 8-bit combinations. Some of the remaining Trans-
mission Characters (Special Characters) are used for func-
tions other than data transmission.
The primary rationale for use of a Transmission Code is to
improve the transmission characteristics of a serial link. The
encoding defined by the Transmission Code ensures that suf-
ficient transitions are present in the serial bit stream to make
clock recovery possible at the Receiver. Such encoding also
greatly increases the likelihood of detecting any single or mul-
tiple bit errors that may occur during transmission and recep-
tion of information. In addition, some Special Characters of the
Transmission Code selected by Fibre Channel Standard con-
sist of a distinct and easily recognizable bit pattern (the Special
Character Comma) that assists a Receiver in achieving word
alignment on the incoming bit stream.
Notation Conventions
The documentation for the 8B/10B Transmission Code uses
letter notation for the bits in an 8-bit byte. Fibre Channel Stan-
dard notation uses a bit notation of A, B, C, D, E, F, G, H for
the 8-bit byte for the raw 8-bit data, and the letters a, b, c, d, e,
i, f, g, h, j for encoded 10-bit data. There is a correspondence
between bit A and bit a, B and b, C and c, D and d, E and e, F
and f, G and g, and H and h. Bits i and j are derived, respec-
tively, from (A,B,C,D,E) and (F,G,H).
The bit labeled A in the description of the 8B/10B Transmission
Code corresponds to bit 0 in the numbering scheme of the FC-
2 specification, B corresponds to bit 1, as shown below.
FC-2 bit designation
—
HOTLink D/Q designation
—
7
8B/10B bit designation
—
To clarify this correspondence, the following example shows
the conversion from an FC-2 Valid Data Byte to a Transmission
Character (using 8B/10B Transmission Code notation)
FC-2
45
Bits:
7
6
6
5
5
4
4
E
3
3
D C B
2
2
1
1
0
0
A
H G F
7654 3210
0100 0101
Converted to 8B/10B notation (note carefully that the order of
bits is reversed):
Data Byte Name
D5.2
Bits:
ABCDE FGH
10100
010
Translated to a transmission Character in the 8B/10B Trans-
mission Code:
Bits:
abcdeifghj
1010010101
Each valid Transmission Character of the 8B/10B Transmis-
sion Code has been given a name using the following conven-
tion: cxx.y, where c is used to show whether the Transmission
Character is a Data Character (c is set to D, and the SC/D* pin
is LOW) or a Special Character (c is set to K, and the SC/D*
pin is HIGH). When c is set to D, xx is the decimal value of the
binary number composed of the bits E, D, C, B, and A in that
order, and the y is the decimal value of the binary number
composed of the bits H, G, and F in that order. When c is set
to K, xx and y are derived by comparing the encoded bit pat-
terns of the Special Character to those patterns derived from
encoded Valid Data bytes and selecting the names of the pat-
terns most similar to the encoded bit patterns of the Special
Character.
Under the above conventions, the Transmission Character
used for the examples above, is referred to by the name D5.2.
The Special Character K29.7 is so named because the first six
bits (abcdei) of this character make up a bit pattern similar to
that resulting from the encoding of the unencoded 11101 pat-
tern (29), and because the second four bits (fghj) make up a
bit pattern similar to that resulting from the encoding of the
unencoded 111 pattern (7).
Note:
This definition of the 10-bit Transmission Code is based
on (and is in basic agreement with) the following references,
which describe the same 10-bit transmission code.
A.X. Widmer and P.A. Franaszek.
“
A DC-Balanced, Parti-
tioned-Block, 8B/10B Transmission Code
”
IBM Journal of Re-
search and Development
, 27, No. 5: 440-451 (September, 1983).
U.S. Patent 4,486,739. Peter A. Franaszek and Albert X. Wid-
mer.
“
Byte-Oriented DC Balanced (0.4) 8B/10B Partitioned
Block Transmission Code
”
(December 4, 1984).
Fibre Channel Physical and Signaling Interface (ANS X3.230-
1994 ANSI FC-PH Standard).
IBM Enterprise Systems Architecture/390 ESCON I/O Inter-
face (document number SA22-7202).
8B/10B Transmission Code
The following information describes how the tables shall be
used for both generating valid Transmission Characters (en-
coding) and checking the validity of received Transmission
Characters (decoding). It also specifies the ordering rules to
be followed when transmitting the bits within a character and
the characters within the higher-level constructs specified by
the standard.
Transmission Order
Within the definition of the 8B/10B Transmission Code, the bit
positions of the Transmission Characters are labeled a, b, c, d,
e, i, f, g, h, j. Bit
“
a
”
shall be transmitted first followed by bits b,
c, d, e, i, f, g, h, and j in that order. (Note that bit i shall be
transmitted between bit e and bit f, rather than in alphabetical
order.)
Valid and Invalid Transmission Characters
The following tables define the valid Data Characters and valid
Special Characters (K characters), respectively. The tables are
used for both generating valid Transmission Characters (en-
coding) and checking the validity of received Transmission
Characters (decoding). In the tables, each Valid-Data-byte or
Special-Character-code entry has two columns that represent
two (not necessarily different) Transmission Characters. The
two columns correspond to the current value of the running
disparity (
“
Current RD
–”
or
“
Current RD+
”
). Running disparity
is a binary parameter with either the value negative (
–
) or the
value positive (+).
After powering on, the Transmitter may assume either a posi-
tive or negative value for its initial running disparity. Upon
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C964A | Bus Interface Logic Circuit |
| CY7C964A-UM | Bus Interface Logic Circuit |
| CY7C964A-UMB | Bus Interface Logic Circuit |
| CY7C964A-ASC | Bus Interface Logic Circuit |
| CY7C964A-NC | Bus Interface Logic Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C955-NC | 制造商:Cypress Semiconductor 功能描述:SONET Transceiver, AX ATM-SONET/SDH Transceiver |
| CY7C960-UMB | 制造商:Cypress Semiconductor 功能描述: |
| CY7C9611-NC | 功能描述:IC PHYSICAL LAYER DEVICE RoHS:否 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A |
| CY7C964A-GMB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CY7C964AUM | 制造商: 功能描述: 制造商:CY 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。