參數資料
型號： AT32AP7002-CTUT
廠商： Atmel
文件頁數： 79/83頁
文件大?。?/td> 0K
描述： IC MCU 32BIT AVR32 196-CBGA
產品培訓模塊： MCU Product Line Introduction
標準包裝： 945
系列： AVR®32 AP7
核心處理器： AVR
芯體尺寸： 32-位
速度： 150MHz
連通性： EBI/EMI，I²C，MMC，PS2，SPI，SSC，UART/USART，USB
外圍設備： AC'97，DMA，I²S，LCD，POR，PWM，WDT
輸入/輸出數： 85
程序存儲器類型： ROMless
RAM 容量： 32K x 8
電壓 - 電源 (Vcc/Vdd)： 1.65 V ~ 1.95 V
數據轉換器： D/A 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 196-CBGA
包裝： 托盤
配用： ATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMR
ATNGW100-ND - KIT AVR32 NETWORK GATEWAY
ATSTK1000-ND - KIT STARTER FOR AVR32AP7000
dsPIC30F2010
DS70118J-page 72
2011 Microchip Technology Inc.
12.1
Timer2 and Timer3 Selection Mode
Each output compare channel can select between one
of two 16-bit timers: Timer2 or Timer3.
The selection of the timers is controlled by the OCTSEL
bit (OCxCON<3>). Timer2 is the default timer resource
for the Output Compare module.
12.2
Simple Output Compare Match
Mode
When control bits OCM<2:0> (OCxCON<2:0>) = 001,
010
or 011, the selected output compare channel is
configured for one of three simple Output Compare
Match modes:
Compare forces I/O pin low
Compare forces I/O pin high
Compare toggles I/O pin
The OCxR register is used in these modes. The OCxR
register is loaded with a value and is compared to the
selected incrementing timer count. When a compare
occurs, one of these Compare Match modes occurs. If
the counter resets to zero before reaching the value in
OCxR, the state of the OCx pin remains unchanged.
12.3
Dual Output Compare Match Mode
When control bits OCM<2:0> (OCxCON<2:0>) = 100
or 101, the selected output compare channel is config-
ured for one of two Dual Output Compare modes,
which are:
Single Output Pulse mode
Continuous Output Pulse mode
12.3.1
SINGLE PULSE MODE
For the user to configure the module for the generation
of a single output pulse, the following steps are
required (assuming timer is off):
Determine instruction cycle time TCY.
Calculate desired pulse width value based on TCY.
Calculate time to start pulse from timer start value
of 0x0000.
Write pulse width start and stop times into OCxR
and OCxRS compare registers (x denotes
channel 1, 2).
Set timer period register to value equal to, or
greater than, value in OCxRS compare register.
Set OCM<2:0> = 100.
Enable timer, TON (TxCON<15>) = 1.
To initiate another single pulse, issue another write to
set OCM<2:0> = 100.
12.3.2
CONTINUOUS PULSE MODE
For the user to configure the module for the generation
of a continuous stream of output pulses, the following
steps are required:
Determine instruction cycle time TCY.
Calculate desired pulse value based on TCY.
Calculate timer to start pulse width from timer start
value of 0x0000.
Write pulse width start and stop times into OCxR
and OCxRS (x denotes channel 1, 2) compare
registers, respectively.
Set timer period register to value equal to, or
greater than, value in OCxRS compare register.
Set OCM<2:0> = 101.
Enable timer, TON (TxCON<15>) = 1.
12.4
Simple PWM Mode
When control bits OCM<2:0> (OCxCON<2:0>) = 110
or 111, the selected output compare channel is config-
ured for the PWM mode of operation. When configured
for the PWM mode of operation, OCxR is the main latch
(read-only) and OCxRS is the secondary latch. This
enables glitchless PWM transitions.
The user must perform the following steps in order to
configure the output compare module for PWM
operation:
1.
Set the PWM period by writing to the appropriate
period register.
2.
Set the PWM duty cycle by writing to the OCxRS
register.
3.
Configure the output compare module for PWM
operation.
4.
Set the TMRx prescale value and enable the
Timer, TON (TxCON<15>) = 1.
12.4.1
INPUT PIN FAULT PROTECTION
FOR PWM
When control bits OCM<2:0> (OCxCON<2:0>) = 111,
the selected output compare channel is again config-
ured for the PWM mode of operation, with the
additional feature of input fault protection. While in this
mode, if a logic ‘0’ is detected on the OCFA/B pin, the
respective PWM output pin is placed in the high-imped-
ance input state. The OCFLT bit (OCxCON<4>)
indicates whether a Fault condition has occurred. This
state will be maintained until both of the following
events have occurred:
The external Fault condition has been removed.
The PWM mode has been re-enabled by writing
to the appropriate control bits.
相關PDF資料
PDF描述
VE-B33-IY-F2 CONVERTER MOD DC/DC 24V 50W
VE-B33-CU-B1 CONVERTER MOD DC/DC 24V 200W
AT32UC3C0512C-ALUT IC MCU AVR32 512K FLASH 144LQFP
VE-B32-IY-F3 CONVERTER MOD DC/DC 15V 50W
ADUC816BSZ IC MCU 8K FLASH ADC/DAC 52MQFP
相關代理商/技術參數
參數描述
AT32AP7200-CFUR 功能描述:MCU AVR32 200MHZ 324-TFBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:AVR®32 AP7 標準包裝:1,500 系列:AVR® ATtiny 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C，LIN，SPI，UART/USART，USI 外圍設備:欠壓檢測/復位，POR，PWM，溫度傳感器，WDT 輸入/輸出數:16 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:帶卷 (TR)
AT32AP7200-CFUT 功能描述:IC MCU AVR32 AP 200MHZ 324TFBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:AVR®32 AP7 產品培訓模塊:The Ultra-Low Power MSP430 MSP430 Overview MSP430 Design Tools MSP430 Peripherals MSP430x2xx/4xx and Wireless Overview Portable Medical Solutions with MSP430 MSP430 for Utility Metering Solutions MSP430: How to JTAG MSP430, How To Use the Clock System Grace Software Graphical User Interface MCU Overview Driver Library MSP430Ware Overview 標準包裝:1 系列:MSP430x4xx 核心處理器:RISC 芯體尺寸:16-位 速度:8MHz 連通性:SPI，UART/USART 外圍設備:欠壓檢測/復位，LCD，POR，PWM，WDT 輸入/輸出數:48 程序存儲器容量:32KB（32K x 8 + 256B） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-LQFP 包裝:Digi-Reel® 其它名稱:296-26232-6
AT32AP7200-CTUR 功能描述:IC MCU AVR32 AP 200MHZ 324TFBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:AVR®32 AP7 產品培訓模塊:The Ultra-Low Power MSP430 MSP430 Overview MSP430 Design Tools MSP430 Peripherals MSP430x2xx/4xx and Wireless Overview Portable Medical Solutions with MSP430 MSP430 for Utility Metering Solutions MSP430: How to JTAG MSP430, How To Use the Clock System Grace Software Graphical User Interface MCU Overview Driver Library MSP430Ware Overview 標準包裝:1 系列:MSP430x4xx 核心處理器:RISC 芯體尺寸:16-位 速度:8MHz 連通性:SPI，UART/USART 外圍設備:欠壓檢測/復位，LCD，POR，PWM，WDT 輸入/輸出數:48 程序存儲器容量:32KB（32K x 8 + 256B） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-LQFP 包裝:Digi-Reel® 其它名稱:296-26232-6
AT32AP7200-CTUT 功能描述:IC MCU AVR32 AP 200MHZ 324TFBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:AVR®32 AP7 產品培訓模塊:The Ultra-Low Power MSP430 MSP430 Overview MSP430 Design Tools MSP430 Peripherals MSP430x2xx/4xx and Wireless Overview Portable Medical Solutions with MSP430 MSP430 for Utility Metering Solutions MSP430: How to JTAG MSP430, How To Use the Clock System Grace Software Graphical User Interface MCU Overview Driver Library MSP430Ware Overview 標準包裝:1 系列:MSP430x4xx 核心處理器:RISC 芯體尺寸:16-位 速度:8MHz 連通性:SPI，UART/USART 外圍設備:欠壓檢測/復位，LCD，POR，PWM，WDT 輸入/輸出數:48 程序存儲器容量:32KB（32K x 8 + 256B） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-LQFP 包裝:Digi-Reel® 其它名稱:296-26232-6
AT32C16-17JC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 EPROM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*