參數資料
型號: AM79C940JCW
廠商: Advanced Micro Devices, Inc.
英文描述: Media Access Controller for Ethernet (MACE)
中文描述: 媒體訪問控制器(MACE發生以太網)
文件頁數: 71/122頁
文件大?。?/td> 914K
代理商: AM79C940JCW
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
AMD
71
Am79C940
Physical Address
(PADR [47–00])
(REG ADDR 21)
PADR [47–00]
This 48-bit value represents the unique node value as-
signed by the IEEE and used for internal address com-
parison. After a hardware or software reset and before
the ENRCV bit in the MAC Configuration Control regis-
ter has been set, the Physical Address can be accessed
by setting the PHYADDR bit in the Internal Address
Configuration register (REG ADDR 18) and then by per-
forming 6 reads or writes to the Physical Address. Once
ENRCV has been set, the ADDRCHG bit in the Internal
Address Configuration register must be set and be
polled until it is cleared by the MACE device before set-
ting the PHYADDR bit and before accessing of the
Physical Address is allowed. The first bit of the incoming
address must be a 0 for a physical address. The incom-
ing address is compared against the value stored in the
Physical Address register at initialization provided that
the DRCVPA bit in the MAC Configuration Control regis-
ter is cleared.
Missed Packet Count (MPC)
(REG ADDR 24)
MPC [7–0]
The Missed Packet Count (MPC) is a read only 8-bit
counter. The MPC is incremented when the receiver is
unable to respond to a packet which would have nor-
mally been passed to the host. The MPC will be reset to
zero when read. The MACE device will be deafto re-
ceive traffic due to any of the following conditions :
I
The host disabled the receive function by clearing
the ENRCV bit in the MAC Configuration Control
register.
I
A Receive FIFO overflow condition exists, and must
be cleared by reading the Receive FIFO and the Re-
ceive Frame Status.
I
The Receive Frame Count (RCVFC) in the FIFO
Frame Count register exceeds its maximum value,
indicating that greater than 15 frames are in the Re-
ceive FIFO.
If the number of received frames that have been missed
exceeds 255, the MPC will roll over and continue count-
ing from zero, the MPCO (Missed Packet Count Over-
flow) bit in the Interrupt Register will be set (at the value
255), and the
INTR
pin will be asserted providing that
MPCOM (Missed Packet Count Overflow Mask) in the
Interrupt Mask Register is clear. MPCOM will be cleared
(the interrupt will be unmasked) after a hardware or soft-
ware reset.
Note that the following conditions apply to the MPC:
I
After hardware or software reset, the MPC will not
increment until the first time the receiver is enabled
(ENRCV = 1). Once the receiver has been enabled,
the MPC will count all missed packet events, re-
gardless of the programming of ENRCV.
I
The packet must pass the internal address match to
be counted. Any of the following address match
conditions will increment MPC while the receiver is
deaf
Physical Address match;
Logical Address match;
Broadcast reception;
Any receive in promiscuous mode (PROM = 1 in the
MAC Configuration Control register);
EADI feature match mode and
EAM
is asserted;
EADI feature reject mode and
EAR
is not asserted.
I
Any packet which suffers a collision within the slot
time will not be counted.
I
Runt packets will not be counted unless RPA in the
User Test Register is enabled.
I
Packets which pass the address match criteria but
experience FCS or Framing errors will be counted,
since they are normally passed to the host.
Runt Packet Count (RNTPC)
(REG ADDR 26)
RNTPC [7–0]
The Runt Packet Count (RNTPC) is a read only 8-bit
counter, incremented when the receiver detects a runt
packet that is addressed to this node. Runt packets are
defined as received frames which passed the internal
address match criteria but did not contain a minimum of
64-bytes of data after SFD. Note that the RNTPC value
returned in the Receive Frame Status (RFS2) will freeze
at a value of 255, whereas this register based version of
RNTPC is free running. The value will roll over after 255
runt packets have been detected, setting the RNTPCO
bit (in the Interrupt Register and asserting the
INTR
pin if
the corresponding mask bit (RNTPCOM in the Interrupt
Mask Register) is cleared. RNTPC will be reset to zero
when read.
相關PDF資料
PDF描述
AM79C940KCW Media Access Controller for Ethernet (MACE)
AM79C960 PCnetTM-ISA Single-Chip Ethernet Controller
AM79C960KC PCnetTM-ISA Single-Chip Ethernet Controller
AM79C960KCW PCnetTM-ISA Single-Chip Ethernet Controller
AM79C961AKCW PCnet ⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
相關代理商/技術參數
參數描述
AM79C940JI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller
AM79C940JI/W 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Media Access Controller for Ethernet (MACE⑩)
AM79C940KC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller
AM79C940KC/W 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Media Access Controller for Ethernet (MACE⑩)
AM79C940KCW 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Media Access Controller for Ethernet (MACE)