- 您現在的位置：買賣IC網 > PDF目錄11210 > ADUC7061BCPZ32-RL (Analog Devices Inc)IC MCU 16/32BIT 32KB 32LFCSP PDF資料下載
參數資料
| 型號： | ADUC7061BCPZ32-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 108/108頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 16/32BIT 32KB 32LFCSP |
| 產品變化通告： | ADuC7060/1 Idd Specification Change 01/Feb/2010 |
| 設計資源： | USB Based Temperature Monitor Using ADuC7061 and an External RTD (CN0075) 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) |
| 標準包裝： | 5,000 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 10MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | POR，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 8 |
| 程序存儲器容量： | 32KB（16K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 32 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.375 V ~ 2.625 V |
| 數據轉換器： | A/D 5x24b，8x24b，D/A 1x14b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁當前第108頁
Data Sheet
ADuC7060/ADuC7061
Rev. D | Page 99 of 108
Table 109. SPICON MMR Bit Designations
Bit
Name
Description
15:14
SPIMDE
SPI IRQ mode bits. These bits are configured when transmit/receive interrupts occur in a transfer.
[00] = transmit interrupt occurs when 1 byte has been transferred. Receive interrupt occurs when one or more bytes
have been received into the FIFO.
[01] = transmit interrupt occurs when 2 bytes have been transferred. Receive interrupt occurs when two or more
bytes have been received into the FIFO.
[10] = transmit interrupt occurs when 3 bytes have been transferred. Receive interrupt occurs when three or more
bytes have been received into the FIFO.
[11] = transmit interrupt occurs when 4 bytes have been transferred. Receive interrupt occurs when the receive FIFO
is full or 4 bytes are present.
13
SPITFLH
SPI transmit FIFO flush enable bit.
Set this bit to flush the transmit FIFO. This bit does not clear itself and should be toggled if a single flush is required. If
this bit is left high, then either the last transmitted value or 0x00 is transmitted, depending on the SPIZEN bit. Any
writes to the transmit FIFO are ignored while this bit is set.
Clear this bit to disable transmit FIFO flushing.
12
SPIRFLH
SPI receive FIFO flush enable bit.
Set this bit to flush the receive FIFO. This bit does not clear itself and should be toggled if a single flush is required. If
this bit is set, all incoming data is ignored and no interrupts are generated. If set and SPITMDE = 0, a read of the
receive FIFO initiates a transfer.
Clear this bit to disable receive FIFO flushing.
11
SPICONT
Continuous transfer enable.
Set by user to enable continuous transfer. In master mode, the transfer continues until no valid data is available in the
transmit register.
A
SSEE
A
is asserted and remains asserted for the duration of each 8-bit serial transfer until the transmit
register is empty.
Cleared by user to disable continuous transfer. Each transfer consists of a single 8-bit serial transfer. If valid data exists
in the SPITX register, then a new transfer is initiated after a stall period of one serial clock cycle.
10
SPILP
Loopback enable bit.
Set by user to connect MISO to MOSI and test software.
Cleared by user to be in normal mode.
9
SPIOEN
Slave MISO output enable bit.
Set this bit for MISO to operate as normal.
Clear this bit to disable the output driver on the MISO pin. The MISO pin is open drain when this bit is cleared.
8
SPIROW
SPIRX overflow overwrite enable.
Set by user, the valid data in the receive register is overwritten by the new serial byte received.
Cleared by user, the new serial byte received is discarded.
7
SPIZEN
SPI transmit zeros when transmit FIFO is empty.
Set this bit to transmit 0x00 when there is no valid data in the transmit FIFO.
Clear this bit to transmit the last transmitted value when there is no valid data in the transmit FIFO.
6
SPITMDE
SPI transfer and interrupt mode.
Set by user to initiate transfer with a write to the SPITX register. Interrupt occurs only when the transmit FIFO is empty.
Cleared by user to initiate transfer with a read of the SPI register. Interrupt occurs only when the receive FIFO is full.
5
SPILF
LSB first transfer enable bit.
Set by user, the LSB is transmitted first.
Cleared by user, the MSB is transmitted first.
4
SPIWOM
SPI wired or mode enable bit.
Set to 1 to enable the open-drain data output enable. External pull-ups are required on data out pins.
Clear for normal output levels.
3
SPICPO
Serial clock polarity mode bit.
Set by user, the serial clock idles high.
Cleared by user, the serial clock idles low.
2
SPICPH
Serial clock phase mode bit.
Set by user, the serial clock pulses at the beginning of each serial bit transfer.
Cleared by user, the serial clock pulses at the end of each serial bit transfer.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B2L-IW-F4 | CONVERTER MOD DC/DC 28V 100W |
| ATMEGA8535L-8JU | MCU AVR 8K ISP FLASH MEM 44-PLCC |
| VI-B2L-IW-F3 | CONVERTER MOD DC/DC 28V 100W |
| ATMEGA8535L-8PU | IC AVR MCU 8K 8MHZ 3V 40DIP |
| VI-B2L-IW-F2 | CONVERTER MOD DC/DC 28V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC70SMARTLINKRL7 | 制造商:Analog Devices 功能描述: |
| ADUC70TEL | 制造商:Analog Devices 功能描述:FLASH ARM +5-CH 12BIT ADC - Trays |
| ADUC70TEL-RL7 | 制造商:Analog Devices 功能描述: |
| ADUC7120BBCZ | 制造商:Analog Devices 功能描述:- Rail/Tube |
| ADUC7120BBCZ-RL | 制造商:Analog Devices 功能描述:- Tape and Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。