- 您現在的位置：買賣IC網 > PDF目錄375267 > ADSP-21267 (Analog Devices, Inc.) Preliminary Technical Data PDF資料下載
參數資料
| 型號： | ADSP-21267 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Preliminary Technical Data |
| 中文描述： | 初步技術數據 |
| 文件頁數： | 11/44頁 |
| 文件大?。?/td> | 454K |
| 代理商： | ADSP-21267 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
ADSP-21267
Rev. PrA
|
Page 11 of 44
|
January 2004
PRELIMINARY TECHNICAL DATA
DAI_P20-1
I/O/T
Three-state with
programmable pull-
up
Digital Audio Interface Pins
. These pins provide the physical interface to the SRU.
The SRU configuration registers define the combination of on-chip peripheral
inputs or outputs connected to the pin and to the pin’s output enable. The config-
uration registers of these peripherals then determines the exact behavior of the pin.
Any input or output signal present in the SRU may be routed to any of these pins.
The SRU provides the connection from the Serial ports, Input data port, precision
clock generators and timers to the DAI_P20-1 pins These pins have internal 22.5 K
pull-up resistors which are enabled on reset. These pull-ups can be disabled in the
DAI_PIN_PULLUP register.
Serial Peripheral Interface Clock Signal
. Driven by the master, this signal controls
the rate at which data is transferred. The master may transmit data at a variety of
baud rates. SPICLK cycles once for each bit transmitted. SPICLK is a gated clock that
is active during data transfers, only for the length of the transferred word. Slave
devices ignore the serial clock if the slave select input is driven inactive (HIGH).
SPICLK is used to shift out and shift in the data driven on the MISO and MOSI lines.
The data is always shifted out on one clock edge and sampled on the opposite edge
of the clock. Clock polarity and clock phase relative to data are programmable into
the SPICTL control register and define the transfer format. SPICLK has a 22.5 K
internal pull-up resistor.
Serial Peripheral Interface Slave Device Select
. An active low signal used to select
the DSP as an SPI slave device. This input signal behaves like a chip select, and is
provided by the master device for the slave devices. In multi-master mode the DSPs
SPIDS signal can be driven by a slave device to signal to the DSP (as SPI master) that
an error has occurred, as some other device is also trying to be the master device.
If asserted low when the device is in master mode, it is considered a multi-master
error. For a single-master, multiple-slave configuration where flag pins are used, this
pin must be tied or pulled high to V
DDEXT
on the master device. For ADSP-21267 to
ADSP-21267 SPI interaction, any of the master ADSP-21267's flag pins can be used
to drive the SPIDS signal on the ADSP-21267 SPI slave device.
SPI Master Out Slave In
. If the ADSP-21267 is configured as a master, the MOSI pin
becomes a data transmit (output) pin, transmitting output data. If the ADSP-21267
is configured as a slave, the MOSI pin becomes a data receive (input) pin, receiving
input data. In an ADSP-21267 SPI interconnection, the data is shifted out from the
MOSI output pin of the master and shifted into the MOSI input(s) of the slave(s).
MOSI has a 22.5 K
internal pull-up resistor.
SPI Master In Slave Out
. If the ADSP-21267 is configured as a master, the MISO pin
becomes a data receive (input) pin, receiving input data. If the ADSP-21267 is
configured as a slave, the MISO pin becomes a data transmit (output) pin, trans-
mitting output data. In an ADSP-21267 SPI interconnection, the data is shifted out
from the MISO output pin of the slave and shifted into the MISO input pin of the
master. MISO has a 22.5K
internal pull-up resistor. MISO can be configured as O/D
by setting the OPD bit in the SPICTL register.
Note:
Only one slave is allowed to transmit data at any given time.
To enable
broadcast transmission to multiple SPI-slaves, the DSP's MISO pin may be disabled
by setting (=1) bit 5 (DMISO) of the SPICTL register.
Boot Configuration Select
. Selects the boot mode for the DSP. The BOOTCFG pins
must be valid before reset is asserted. See
Table 4 on page 13
for a description of
the boot modes.
SPICLK
I/O
Three-state with
pull-up enabled
SPIDS
I
Input only
MOSI
I/O (O/D)
Three-state with
pull-up enabled
MISO
I/O (O/D)
Three-state with
pull-up enabled
BOOTCFG1-0
I
Input only
Table 2. Pin Descriptions (Continued)
Pin
Type
State During &
After Reset
Function
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21267SKBCZ-X | Preliminary Technical Data |
| ADSP-21267SKSTZ-X | Preliminary Technical Data |
| ADSP-21362 | SHARC Processor |
| ADSP-21362BBC-1AA | SHARC Processor |
| ADSP-21362BBCZ-1AA | SHARC Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21267SKBCZ-X | 制造商:AD 制造商全稱:Analog Devices 功能描述:Preliminary Technical Data |
| ADSP-21267SKSTZ-X | 制造商:AD 制造商全稱:Analog Devices 功能描述:Preliminary Technical Data |
| ADSP-21362 | 制造商:AD 制造商全稱:Analog Devices 功能描述:SHARC Processor |
| adsp-21362bbc-1aa | 制造商:Analog Devices 功能描述: |
| ADSP-21362BBCZ-1AA | 功能描述:數字信號處理器和控制器 - DSP, DSC 333 MHz Processor includes DTCP/SPDIF RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。