- 您現在的位置：買賣IC網 > PDF目錄364551 > 8XC552 (NXP Semiconductors N.V.) 80C51 FAMILY DERIVATIVES PDF資料下載
參數資料
| 型號： | 8XC552 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 80C51 FAMILY DERIVATIVES |
| 中文描述： | 80C51系列衍生物 |
| 文件頁數： | 50/60頁 |
| 文件大?。?/td> | 382K |
| 代理商： | 8XC552 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
Philips Semiconductors
80C51 Family Derivatives
8XC552/562 overview
1996 Aug 06
50
Analog-to-Digital Conversion:
Figure 35 shows the elements of a
successive approximation (SA) ADC. The ADC contains a DAC
which converts the contents of a successive approximation register
to a voltage (VDAC) which is compared to the analog input voltage
(Vin). The output of the comparator is fed to the successive
approximation control logic which controls the successive
approximation register. A conversion is initiated by setting ADCS in
the ADCON register. ADCS can be set by software only or by either
hardware or software.
The software only start mode is selected when control bit ADCON.5
(ADEX) = 0. A conversion is then started by setting control bit
ADCON.3 (ADCS). The hardware or software start mode is selected
when ADCON.5 = 1, and a conversion may be started by setting
ADCON.3 as above or by applying a rising edge to external pin
STADC. When a conversion is started by applying a rising edge, a
low level must be applied to STADC for at least one machine cycle
followed by a high level for at least one machine cycle.
The low-to-high transition of STADC is recognized at the end of a
machine cycle, and the conversion commences at the beginning of
the next cycle. When a conversion is initiated by software, the
conversion starts at the beginning of the machine cycle which
follows the instruction that sets ADCS. ADCS is actually
implemented with two flip-flops: a command flip-flop which is
affected by set operations, and a status flag which is accessed
during read operations.
The next two machine cycles are used to initiate the converter. At
the end of the first cycle, the ADCS status flag is set and a value of
“1” will be returned if the ADCS flag is read while the conversion is in
progress. Sampling of the analog input commences at the end of the
second cycle.
During the next eight machine cycles, the voltage at the previously
selected pin of port 5 is sampled, and this input voltage should be
stable in order to obtain a useful sample. In any event, the input
voltage slew rate must be less than 10V/ms in order to prevent an
undefined result.
The successive approximation control logic first sets the most
significant bit and clears all other bits in the successive
approximation register (10 0000 0000B). The output of the DAC
(50% full scale) is compared to the input voltage Vin. If the input
voltage is greater than VDAC, then the bit remains set; otherwise it
is cleared.
The successive approximation control logic now sets the next most
significant bit (11 0000 0000B or 01 0000 0000B, depending on the
previous result), and VDAC is compared to Vin again. If the input
voltage is greater than VDAC, then the bit being tested remains set;
otherwise the bit being tested is cleared. This process is repeated
until all ten bits have been tested, at which stage the result of the
conversion is held in the successive approximation register. Figure
36 shows a conversion flow chart. The bit pointer identifies the bit
under test. The conversion takes four machine cycles per bit.
The end of the 10-bit conversion is flagged by control bit ADCON.4
(ADCI). The upper 8 bits of the result are held in special function
register ADCH, and the two remaining bits are held in ADCON.7
(ADC.1) and ADCON.6 (ADC.0). The user may ignore the two least
significant bits in ADCON and use the ADC as an 8-bit converter (8
upper bits in ADCH). In any event, the total actual conversion time is
50 machine cycles for the 8XC552 or 24 machine cycles for the
8XC562. ADCI will be set and the ADCS status flag will be reset 50
(or 24) cycles after the command flip-flop (ADCS) is set.
Control bits ADCON.0, ADCON.1, and ADCON.2 are used to control
an analog multiplexer which selects one of eight analog channels
(see Figure 37). An ADC conversion in progress is unaffected by an
external or software ADC start. The result of a completed
conversion remains unaffected provided ADCI = logic 1; a new ADC
conversion already in progress is aborted when the idle or
power-down mode is entered. The result of a completed conversion
(ADCI = logic 1) remains unaffected when entering the idle mode.
Successive
Approximation
Control Logic
Successive
Approximation
Register
DAC
+
–
Start
Stop
V
in
V
DAC
0
1
2
3
4
5
6
t/tau
V
DAC
Full Scale
1
V
in
1/2
3/4
7/8
15/16
29/32
59/64
Figure 35. Successive Approximation ADC
相關PDF資料 |
PDF描述 |
|---|---|
| 8XL51FB | LOW VOLTAGE CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS |
| 8XL51FC | LOW VOLTAGE CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS |
| 8XL51FA | LOW VOLTAGE CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS |
| 8XL54 | LOW VOLTAGE CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS |
| 8XL58 | LOW VOLTAGE CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8XC562 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 FAMILY DERIVATIVES |
| 8XC58 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER |
| 8XC80C32 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit CMOS (low voltage, low power and high speed) microcontroller families |
| 8XF0016-S3P | 制造商:XFMRS 制造商全稱:XFMRS Inc. 功能描述:INDUCTOR |
| 8XF0106-S3P | 制造商:XFMRS 制造商全稱:XFMRS Inc. 功能描述:INDUCTOR |
發布緊急采購，3分鐘左右您將得到回復。